1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U
4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMSDTL23053/11A AEROSPACE MATERIAL SPECIFICATION AMS-DTL-23053/11 REV. A Issued 1999-07 Revis
5、ed 2012-08 Superseding AMS-DTL-23053/11 Insulation Sleeving, Electrical, Heat Shrinkable, Fluorinated Ethylene Propylene, Non-Crosslinked FSC 5970 RATIONALE Revise to include comments received by the government and industry, update references, align specification with SAE guidelines, and review spec
6、ification for known technical problems. The requirements for acquiring the sleeving described herein shall consist of this specification sheet and the issue of the following specification listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) specified in th
7、e solicitation: MIL-DTL-23053. REQUIREMENTS Polymer type: The base polymer used in formulating this sleeving shall be fluorinated ethylene propylene. Continuous operating temperature range: -88 F (-67 C) to +392 F (+200 C). Color: The sleeving shall be furnished in clear (water white to transparent
8、blue), the as manufactured color. (See 1.2.1) Class: The sleeving shall be furnished in the following classes, as specified (See 6.4a and 6.8): Class 1 - Normal shrink ratio, Heavy Wall Class 2 - High shrink ratio, Medium Wall Longitudinal change: 15 percent SAE AMS-DTL-23053/11A Page 2 of 5 Militar
9、y part number: The Military part number shall consist of this specification sheet and dash numbers as follows: M23053/11 - X XX - X Example: Class 2, 0.750 inch (19.1 mm) as supplied ID sleeving shall be identified as M23053/11-207-C. TABLE 1 - CONSTRUCTION DETAILS, INCHES (MM) 1/ Military part numb
10、er 1/ As supplied ID minimum After unrestricted shrinkage ID maximum Wall Thickness 2/ Class 1 M23053/11-101-C 0.031(0.79) 0.027(0.69) 0.008 0.002(0.203 0.051) M23053/11-102-C 0.036(0.91) 0.032(0.81) 0.008 0.002(0.203 0.051) M23053/11-103-C 0.045(1.14) 0.039(0.99) 0.008 0.002(0.203 0.051) M23053/11-
11、104-C 0.060(1.52) 0.049(1.24) 0.008 0.002(0.203 0.051) M23053/11-105-C 0.075(1.91) 0.061(1.55) 0.009 0.002(0.229 0.051) M23053/11-106-C 0.092(2.34) 0.072(1.83) 0.009 0.002(0.229 0.051) M23053/11-107-C 0.115(2.92) 0.089(2.26) 0.009 0.002(0.229 0.051) M23053/11-108-C 0.141(3.58) 0.114(2.90) 0.010 0.00
12、3(0.254 0.076) M23053/11-109-C 0.158(4.01) 0.124(3.15) 0.010 0.003(0.254 0.076) M23053/11-110-C 0.180(4.57) 0.143(3.63) 0.010 0.003(0.254 0.076) M23053/11-111-C 0.197(5.00) 0.158(4.01) 0.011 0.004(0.279 0.102) M23053/11-112-C 0.225(5.72) 0.180(4.57) 0.011 0.004(0.279 0.102) M23053/11-113-C 0.248(6.3
13、0) 0.198(5.03) 0.011 0.004(0.279 0.102) M23053/11-114-C 0.290(7.37) 0.226(5.74) 0.011 0.004(0.279 0.102) M23053/11-115-C 0.310(7.87) 0.249(6.32) 0.011 0.004(0.279 0.102) M23053/11-116-C 0.365(9.27) 0.280(7.11) 0.012 0.004(0.305 0.102) M23053/11-117-C 0.400(10.16) 0.311(7.90) 0.012 0.004(0.305 0.102)
14、 M23053/11-118-C 0.440(11.18) 0.349(8.86) 0.012 0.004(0.305 0.102) M23053/11-119-C 0.500(12.70) 0.383(9.73) 0.015 0.004(0.381 0.102) M23053/11-120-C 0.580(14.73) 0.448(11.38) 0.020 0.004(0.508 0.102) M23053/11-121-C 0.666(16.92) 0.510(12.95) 0.020 0.004(0.508 0.102) M23053/11-122-C 0.830(21.08) 0.63
15、7(16.18) 0.025 0.004(0.635 0.102) M23053/11-123-C 1.000(25.40) 0.764(19.41) 0.030 0.004(0.762 0.102) M23053/11-124-C 1.170(29.72) 0.891(22.63) 0.035 0.004(0.889 0.102) M23053/11-125-C 1.300(33.02) 1.000(25.40) 0.020 0.004(0.508 0.102) M23053/11-126-C 1.330(33.78) 1.020(25.91) 0.035 0.004(0.889 0.102
16、) M23053/11-127-C 1.700(43.18) 1.300(33.02) 0.020 0.004(0.508 0.102) M23053/11-128-C 2.100(53.34) 1.700(4318) 0.020 0.004(0.508 0.102) M23053/11-129-C 2.600(66.04) 2.100(53.34) 0.020 0.004(0.508 0.102) M23053/11-130-C 3.100(78.74) 2.600(66.04) 0.020 0.004(0.508 0.102) M23053/11-131-C 3.500(88.90) 3.
17、100(78.74) 0.020 0.004(0.508 0.102) M23053/11-132-C 4.300(109.22) 3.500(88.90) 0.020 0.004(0.508 0.102) M23053/11-133-C 1.500(38.10) 1.145(29.08) 0.035 0.004(0.889 0.102) M23053/11-134-C 1.666(42.32) 1.270(32.26) 0.035 0.004(0.889 0.102) M23053/11-135-C 1.833(46.56) 1.390(35.31) 0.035 0.004(0.889 0.
18、102) M23053/11-136-C 2.000(50.80) 1.570(39.88) 0.035 0.004(0.889 0.102) Color code designator (See 1.2.1) Size identifier (See Table 1) Class (Where no classes are specified in the specification sheet, the numeric “0” is used) Specification sheet SAE AMS-DTL-23053/11A Page 3 of 5 TABLE 1 - CONSTRUCT
19、ION DETAILS, INCHES (MM) 1/ (CONT.) Military part number 1/ As supplied ID minimum After unrestricted shrinkage ID maximum Wall Thickness 2/ Class 2 M23053/11-201-C 0.093(2.36) 0.056(1.42) 0.008 0.003(0.203 0.076) M23053/11-202-C 0.125(3.18) 0.075(1.91) 0.010 0.003(0.254 0.076) M23053/11-203-C 0.188
20、(4.78) 0.115(2.92) 0.010 0.003(0.254 0.076) M23053/11-204-C 0.250(6.35) 0.150(3.81) 0.010 0.003(0.254 0.076) M23053/11-205-C 0.375(9.53) 0.225(5.72) 0.012 0.003(0.305 0.076) M23053/11-206-C 0.500(12.70) 0.300(7.62) 0.015 0.004(0.381 0.102) M23053/11-207-C 0.750(19.05) 0.450(11.43) 0.020 0.004(0.508
21、0.102) M23053/11-208-C 1.000(25.40) 0.600(15.24) 0.025 0.005(0.635 0.127) M23053/11-209-C 1.500(38.10) 0.900(22.86) 0.030 0.005(0.762 0.127) M23053/11-210-C 2.000(50.80) 1.200(30.48) 0.030 0.005(0.762 0.127) 1/ Diameter limits for the object to be enclosed shall be as recommended in technical data.
22、2/ Wall thickness values are less when shrinkage is restricted Unrestricted shrinkage: Test method 4.6.5: Sleeving 1 inch and below: 410 F 10 (210 C 6). Sleeving over 1 inch dia. 430 F 10 (221 C 6). SAE AMS-DTL-23053/11A Page 4 of 5 TABLE 2 PHYSICAL PROPERTIES. 1/ Characteristic Requirement Test pro
23、cedure and condition As supplied: ID, minimum Table 1 4.6.3.1.1 Restricted shrinkage No cracks 4.6.6 347 F 4 (175 C 2) Voltage withstand Pass 4.6.6.3 Clarity stability Pass 4.6.16 347 F 2 (175 C 1), 24 hours After unrestricted shrinkage: ID, maximum Table 1 4.6.3.1.2 Wall thickness Table 1 4.6.3.2 T
24、ensile strength psi (MPa), minimum 2000(13.8) 4.6.13 ASTM D 638, 2 inches/minute Ultimate elongation, percent, minimum 200 4.6.13 ASTM D 638, 2 inches/minute Dielectric strength, volts/mil (Kv/mm), minimum 500(19.7) 4.6.2 ASTM D 2671 Volume resistivity, Ohm-cm, minimum 10174.6.2 ASTM D 876 Water abs
25、orption, percent, maximum 0.01 4.6.2 ASTM D 570, 24 hours at 73 F (23 C) Low temperature flexibility No cracks 4.6.7.1 -85 F 2 (-65 C 1) Heat resistance, properties after: 4.6.9 482 F 5.4 (250 C 3), 96 hours Tensile strength, psi (MPa) , minimum 2000(13.8) Ultimate elongation, percent, minimum 200 D
26、ielectric strength, volts/mil (Kv/mm), minimum 500(19.7) Flammability Non-flammable 2/ Corrosion Non-corrosive 2/ SAE AMS-DTL-23053/11A Page 5 of 5 TABLE 2 PHYSICAL PROPERTIES. 1/ (CONT.) Characteristic Requirement Test procedure and condition Fluid resistance No change 2/ Fungus resistance No growt
27、h 2/ 1/ Unless otherwise specified, the requirements, test procedures and conditions are for all classes. 2/ Because of their relative inertness, MIL-I-23053/11 sleevings are not normally subject to these requirements. However, the acquiring activity (See 6.2) may, at its option, specify performance
28、 of any or all of these requirements. Storage life conditions: Supplier shall certify to storage at 65 to 95 F (18 to 35 C) for 4 years. Conformance to 3.5. See 3.5.2 for storage life extension. Intended use: Heat shrinkable fluorinated ethylene propylene sleevings are intended for use in high tempe
29、rature applications. NOTES A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete re
30、vision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. PREPARED BY AE-8D WIRE AND CABLE COMMITTEE
