欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5894C-2009 Cobalt Alloys Bars Sheet and Plate 60Co - 28Cr - 4 5W - 1 15C Solution Heat Treated《固溶热处理的60Co-28Cr-4 5W-1 15C钴合金棒材 片材及板材》.pdf

    • 资源ID:1022270       资源大小:47.26KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5894C-2009 Cobalt Alloys Bars Sheet and Plate 60Co - 28Cr - 4 5W - 1 15C Solution Heat Treated《固溶热处理的60Co-28Cr-4 5W-1 15C钴合金棒材 片材及板材》.pdf

    1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

    2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2009 SAE International All rights reserved. No part of this publication ma

    3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

    4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5894CAEROSPACEMATERIALSPECIFICATIONAMS5894 REV. C Issued 1993-01 Revised 2009-09 Superseding

    5、 AMS5894B Cobalt Alloys, Bars, Sheet, and Plate 60Co 28Cr 4.5W 1.15C Solution Heat Treated RATIONALEAMS5894C revises condition of sheet and plate (3.2.1), adds product form to the reporting requirements (4.4) and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specific

    6、ation covers a cobalt alloy in the form of sheet and plate up to 1 inch (25 mm) in nominal thickness or round bars up to 3 1/2 inches (89 mm) in nominal diameter.1.2 Application These products have been used typically for parts requiring wear resistance and minimum galling or seizing tendencies at r

    7、oom and elevated temperatures, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of

    8、a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale,

    9、PA 15096-0001, Tel: 877-606-7323 (inside USA or Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2261 Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and Wire AMS2269 Chemical Check Analysis Limits, Nickel, Nickel Alloys and Cobalt Alloys AMS2371 Quality Assurance Sampling and T

    10、esting, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock AMS2750 Pyrometry AMS2806 Identification, Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys AMS2807 Identification, Carbon and Low-Alloy

    11、Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS5894C Page 2 of 52.2 ASTM Publications Availabl

    12、e from ASTM International, 100 Barr Harbor, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM A 480/A 480M Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM E 8/E 8M Tension Testing of Metallic Materials ASTM E 18 Rockwell Hardness of Me

    13、tallic Materials ASTM E 354 Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel and Cobalt Alloys 3. TECHNICAL REQUIREMENTS 3.1 CompositionShall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E

    14、 354, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Carbon 0.90 1.40 Manganese 0.5 2.0 Silicon 0.2 2.0 Phosphorus - 0.04 Sulfur - 0.03 Chromium 28.00 32.00 Tungsten 3.50 5.50 Nickel - 3.0 Molybdenum - 1.50 Iron - 3.0 Cobalt

    15、remainder 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2269.3.2 Condition The product shall be supplied in the following condition: 3.2.1 Sheet and Plate Hot rolled, solution heat treated and descaled with a No. 1 finish appearance as described in ASTM A 4

    16、80/A480M. 3.2.2 BarSolution heat treated with a turned or ground finish. 3.3 Solution Heat Treatment The product shall be solution heat treated by heating to 2250 F 25 (1232 C 14), holding at heat for a time commensurate with cross-section but not less than 15 minutes, and cooling at a rate equivale

    17、nt to a still air cool or faster. Pyrometry shall be in accordance with AMS2750. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS5894C Page 3 of 53.4 Properties The product shall conform to th

    18、e following requirements: 3.4.1 Tensile Properties Shall be shown in Table 2; determined in accordance with ASTM E 8/E 8M. Bars shall be tested in the longitudinal direction. Sheet and plate shall be tested in the transverse direction. Reduction in area is not applicable to plate or sheet under 0.5

    19、inches (12.7 mm) in nominal thickness. TABLE 2 - MINIMUM TENSILE PROPERTIES Property Value Tensile Strength 130 ksi (896 MPa) Yield Strength at 0.2% Offset 70 ksi (483 MPa) Elongation in 4D 5% Reduction of Area 7% 3.4.2 HardnessShall be 33 to 43 HRC, determined in accordance with ASTM E 18. 3.5 Qual

    20、ity The product, as received by purchaser shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.6 Tolerances Shall conform to all applicable requirements of the following: 3.6.1 Bars Shall be in accordance with

    21、 AMS2261. 3.6.2 Sheet and Plate Not applicable unless separately agreed upon. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves

    22、the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing S

    23、hall be in accordance with AMS2371. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS5894C Page 4 of 54.4 ReportsThe vendor of the product shall furnish with each shipment a report showing the

    24、results of tests for composition of each heat and for tensile properties and hardness of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5894C, product form, size, and quantity. 4.5 Res

    25、ampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY 5.1 IdentificationShall be as follows: 5.1.1 Bars In accordance with AMS2806. 5.1.2 Sheet and Plate In accordance with AMS2807. 5.2 PackagingThe product shall be prepared for shipment in accordance with commercial

    26、 practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and

    27、when acknowledging purchase orders. 7. REJECTIONS Products not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical re

    28、visions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contai

    29、n editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units an

    30、d are presented only for information. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS5894C Page 5 of 58.4 Purchase documents should specify not less than the following: AMS5894CProduct form and size of product desired Quantity of product desired. PREPARED BY AMS COMMITTEE “F” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-


    注意事项

    本文(SAE AMS 5894C-2009 Cobalt Alloys Bars Sheet and Plate 60Co - 28Cr - 4 5W - 1 15C Solution Heat Treated《固溶热处理的60Co-28Cr-4 5W-1 15C钴合金棒材 片材及板材》.pdf)为本站会员(ownview251)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开