1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2015 SAE InternationalAll rights reserved. No part of this publi
3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out
4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5836DAEROSPACEMATERIAL SPECIFICATIONAMS5836 REV. DIssued 1990-04Reaffirmed 2006-04Revised
5、2015-12Superseding AMS5836CNickel Alloy, Corrosion and Heat-Resistant, Welding Wire72Ni - 3.0Mn - 20Cr - 2.5Cb(Nb)(Composition similar to UNS N06082)RATIONALEAMS5836D has been updated to incorporate the standard quality requirements of AMS materials as the ordering requirements for AWS specified wir
6、e and is a Five Year Review and of this specification.1. SCOPE1.1 FormThis specification covers a corrosion and heat-resistant nickel alloy in the form of welding wire.1.2 ApplicationThis wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated f
7、rom high nickel alloys or combinations of such alloys and corrosion-resistant or plain-carbon steels, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent
8、 specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAva
9、ilable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS2813 Packaging and Marking of Packages of Welding Wire, Standard MethodAMS2814 Packaging and Marking of Packages of Welding Wir
10、e, Premium QualityAMS2816 Identification Welding Wire, Tab Marking MethodSAE INTERNATIONAL AMS5836D Page 2 of 4AMS2819 Identification Welding Wire, Direct Color Code SystemARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire2.2 AWS PublicationsAvailable from American Weldin
11、g Society, 8669 NW 36 Street, #130, Miami, FL 33166-6672, Tel: 1-800-443-9353 or 305-443-9353, www.aws.org.AWS A5.01 Welding Consumables Procurement of Filler Metals and FluxesAWS A5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods3. TECHNICAL REQUIREMENTS3.1 Composition
12、Wire shall meet the technical requirements of AWS A5.14 ERNiCr-3 with the following additional chemistry controls:Cobalt shall be 0.12 max and Tantalum shall be 0.30 max.3.2 Sizes and TolerancesWire shall be supplied in the sizes and to the tolerances specified in AWS A5.14. Smaller diameter wires w
13、hen ordered shall be supplied in sizes and tolerances shown in 3.2.1.3.2.1 DiameterShall be as shown in Table 1.Table 1A - Sizes and diameter tolerances, inch/pound unitsFormNominal DiameterInchToleranceInchPlusToleranceInchMinusCut LengthsSpools 0.030, 0.035, 0.0450.007, 0.010, 0.0150.001 0.00050.0
14、020.0005Table 1B - Sizes and diameter tolerances, SI unitsFormNominal DiameterMillimetersToleranceMillimeterPlusToleranceMillimeterMinusCut LengthsSpools 0.76, 0.89, 1.140.18, 0.25, 0.380.0250.0130.05 0.013SAE INTERNATIONAL AMS5836D Page 3 of 44. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for In
15、spectionThe producer of wire shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements.4.2
16、 Classification of Tests4.2.1 Acceptance TestsComposition (3.1), sizes and tolerances (3.2), and alloy verification (5.1) are acceptance tests and shall be performed on each heat or lot as applicable.4.3 Sampling and TestingShall be in accordance with AWS A5.01 S3, testing schedule 5 or J.4.4 Report
17、sThe producer of wire shall furnish with each shipment a report showing the results of tests for composition of each heat, and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5836D, nominal size, and qu
18、antity.4.5 Resampling and RetestingShall be in accordance with AWS A5.01.5. PREPARATION FOR DELIVERY5.1 Alloy Verification5.1.1 Wire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser and producer. The alloy verification methods of ARP4926 are recom
19、mended.5.1.2 An 8 inch (203 mm) length of wire shall be made accessible at both ends of each spool for alloy verification.5.2 IdentificationShall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser.5.3 Packaging and MarkingShall be in accordance with AMS2813 unle
20、ss AMS2814 or another method is specified by purchaser.6. ACKNOWLEDGMENTA producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONSWire not conforming to this specification, or to modifications authorized by purcha
21、ser, will be subject to rejection.SAE INTERNATIONAL AMS5836D Page 4 of 48. NOTES8.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this docume
22、nt. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensi
23、ons and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS5836DSize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED BY AMS COMMITTEE “F“
