1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5831D AEROSPACE MATERIAL SPECIFICATION AMS5831 REV. D Issued 1990-04 Reaffirme
5、d 2006-04 Revised 2015-12 Superseding AMS5831C Alloy, Corrosion and Heat-Resistant, Welding Wire 29Fe - 22Cr - 21Ni - 18.5Co - 3.2Mo - 2.8W - 0.78Ta 0.30Al - 0.05Zr - 0.05La - 0.20N (Composition similar to UNS R30556) RATIONALE AMS5831D has been updated to incorporate the standard quality requiremen
6、ts of AMS materials as the ordering requirements for AWS specified wire and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion and heat-resistant alloy in the form of welding wire. 1.2 Application This wire has been used typically as fille
7、r metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated from alloys of similar or dissimilar composition, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this spe
8、cification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply
9、. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2813 Packaging and Marking of Packages of Welding Wire, Standard Method AMS2814 Packaging and Markin
10、g of Packages of Welding Wire, Premium Quality AMS2816 Identification Welding Wire, Tab Marking Method SAE INTERNATIONAL AMS5831D Page 2 of 4 AMS2819 Identification, Welding Wire Direct Color Code System ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire 2.2 AWS Publicati
11、ons Available from American Welding Society, 8669 NW 36 Street, #130, Miami, FL 33166-6672, Tel: 1-800-443-9353 or 305-443-9353, www.aws.org. AWS A5.01 Welding Consumables Procurement of Filler Metals and Fluxes AWS A5.9/A5.9M Specification for Bare Stainless Steel Welding Electrodes and Rods 3. TEC
12、HNICAL REQUIREMENTS 3.1 Composition Wire shall meet the technical requirements of AWS A5.9/5.9M, ER3556 and the following: 3.2 Quality Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding opera
13、tions, operation of welding equipment, or properties of the deposited weld metal. 3.3 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances specified in AWS A5.9/5.9M. Smaller diameter wires when ordered shall be supplied in the sizes and tolerances shown in 3.3.1. 3.3.1 Dia
14、meter Shall be as shown in Table 1. Table 1A - Sizes and diameter tolerances, inch/pound units Form Nominal Diameter Inch Tolerance Inch Plus Tolerance Inch Minus Cut Lengths Spools 0.030, 0.035, 0.045 0.007, 0.010, 0.015 0.001 0.0005 0.002 0.0005 Table 1B - Sizes and diameter tolerances, SI units F
15、orm Nominal Diameter Millimeters Tolerance Millimeter Plus Tolerance Millimeter Minus Cut Lengths Spools 0.76, 0.89, 1.14 0.18, 0.25, 0.38 0.025 0.013 0.05 0.013 SAE INTERNATIONAL AMS5831D Page 3 of 4 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of wire shall supply
16、 all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptanc
17、e Tests Composition (3.1), sizes and tolerances (3.3), and alloy verification (5.2.1) are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing Shall be in accordance with AWS A5.01 S3, Testing schedule 5 or J. 4.4 Reports The producer of wire shall furn
18、ish with each shipment a report showing the results of tests for composition of each heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5831D, nominal size, and quantity. 5. PREPARATION FOR DELIVE
19、RY 5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of steel. 5.2 Alloy Verification 5.2.1 Wire from each spool or package of cut
20、 lengths shall be alloy verified by a method acceptable to purchaser and producer. The alloy verification methods of ARP4926 are recommended. 5.2.2 An 8 inch (203 mm) length of wire shall be made accessible at both ends of each spool for alloy verification. 5.3 Identification Shall be in accordance
21、with AMS2816 unless AMS2819 or another method is specified by purchaser. 5.4 Packaging and Marking Shall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser. 6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quota
22、tions and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS5831D Page 4 of 4 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for
23、the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are
24、 not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures
25、are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS5831D Size and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired. PREPARED BY AMS COMMITTEE “F“
