欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5794E-2002 Iron Alloy Corrosion and Heat-Resistant Welding Wire 31Fe - 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0Cb - 0 15N Annealed (UNS R30155)《31Fe 21Cr 20Ni 20Co 3 0Mo 2 5.pdf

    • 资源ID:1022192       资源大小:52.62KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5794E-2002 Iron Alloy Corrosion and Heat-Resistant Welding Wire 31Fe - 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0Cb - 0 15N Annealed (UNS R30155)《31Fe 21Cr 20Ni 20Co 3 0Mo 2 5.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5794F AEROSPACE MATERIAL SPECIFICATION AMS5794 REV. E Issued 1949-08 Revised 2

    5、002-11 Reaffirmed 2013-12 Superseding AMS5794D Iron Alloy, Corrosion and Heat-Resistant, Welding Wire 31Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N Annealed (Composition similar to UNS R30155) RATIONALE AMS5794E has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE:

    6、1.1 Form: This specification covers a corrosion and heat-resistant iron alloy in the form of welding wire.1.2 Application: This wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated from alloys of similar composition, but usage is not limited

    7、to such applications.2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified

    8、. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 2248 Chemical Check Analysis Limits,

    9、Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron AlloysAMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS 2813 Packaging and Marking of Packages of Welding Wire, Stan

    10、dard MethodAMS 2814 Packaging and Marking of Packages of Welding Wire, Premium QualitySAE INTERNATIONAL AMS5794F Page 2 of 6 2.1 (Continued):AMS 2816 Identification, Welding Wire, Tab Marking MethodAMS 2819 Identification, Welding Wire, Direct Color Code SystemARP1876 Weldability Test for Weld Fille

    11、r Metal WireARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org.ASTM E 354 Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron

    12、, Nickel, and Cobalt Alloys3. TECHNICAL REQUIREMENTS: 3.1 Wire Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 354, by spectrochemical methods, or by other analytical methods acceptable to purchaser.3.1.1 Chemical

    13、 analysis of initial ingot, bar, or rod stock before drawing is acceptable provided processes used for drawing or rolling, annealing, and cleaning are conducted to ensure continued conformance to composition requirements.3.1.1.1 Carbon and nitrogen shall also be determined periodically on finished w

    14、ire (See 4.2.2).TABLE 1 CompositionElement min maxCarbon (3.1.1.1) - 0.10Manganese 1.00 2.00Silicon - 1.00Phosphorus - 0.04Sulfur - 0.03Chromium 20.00 22.50Nickel 19.00 21.00Cobalt 18.50 21.00Molybdenum 2.50 3.50Tungsten 2.00 3.00Columbium 0.75 1.25Nitrogen (3.1.1.1) 0.10 0.20Tantalum - 0.05Iron rem

    15、ainderSAE INTERNATIONAL AMS5794F Page 3 of 6 3.1.2 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2248.3.2 Condition: Cold worked, bright finish, and in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment

    16、.3.3 Fabrication: 3.3.1 Wire shall be formed from rod or bar descaled by a process which does not affect the composition of the wire. Surface irregularities inherent with a forming process that does not tear the wire surfaces are acceptable provided the wire conforms to the tolerances of 3.6.3.3.2 B

    17、utt welding is permissible provided both ends to be joined are alloy verified using a method capable of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feedin

    18、g of the wire in machine welding.3.3.3 In-process annealing, if required, between cold rolling or drawing operations, shall be performed in vacuum or protective atmospheres to ensure freedom for surface oxidation and absorption of other extraneous elements.3.3.4 Residual elements, drawing compounds,

    19、 oxides, dirt, oil, dissolved gasses and other foreign material picked up during wire processing that can adversely affect the welding characteristics, the operation of the equipment, or the properties of the weld metal, shall be removed by cleaning processes that will neither result in pitting nor

    20、cause gas absorption by the wire or deposition of substances harmful to welding operations.3.4 Properties: Wire shall conform to the following requirements:3.4.1 Weldability: Melted wire shall flow smoothly and evenly during welding and shall produce acceptable welds. ARP1876 may be used to resolve

    21、disputes.3.4.2 Spooled Wire: Shall conform to 3.4.2.1 and 3.4.2.2.3.4.2.1 Cast: Wire, wound on standard 12-inch (305-mm) diameter spools, shall have imparted to it a curvature such that a specimen sufficient in length to form one loop with a one-inch (25-mm) overlap, when cut from the spool and laid

    22、 on a flat surface, shall form a circle 15 to 50 inches (381 to 1270 mm) in diameter.3.4.2.2 Helix: The specimen on which cast was determined, when laid on a flat surface and measured between adjacent turns, shall show a vertical separation not greater than one inch (25 mm).SAE INTERNATIONAL AMS5794

    23、F Page 4 of 6 3.5 Quality: Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.6 Sizes and Tolerances: W

    24、ire shall be supplied in the sizes and to the tolerances shown in 3.6.1 and 3.6.2.3.6.1 Diameter: Shall be as shown in Table 2.3.6.2 Length: Cut lengths shall be furnished in 18, 27, or 36-inch (457, 686, or 914-mm) lengths, as ordered, and shall not vary more than +0, -0.5 inch (-13 mm) from the le

    25、ngth ordered.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed nec

    26、essary to ensure that the wire conforms to specified requirements.TABLE 2A - Sizes and Diameter Tolerances, Inch/Pound UnitsFormNominal DiameterInchToleranceInchPlus and MinusCut Lengths 0.030, 0.035, 0.045 0.001Cut Lengths 0.062, 0.078, 0.094, 0.125, 0.156, 0.187 0.002Spools 0.007, 0.010, 0.015 0.0

    27、005Spools 0.020, 0.030, 0.035, 0.045 0.001Spools 0.062, 0.078, 0.094 0.002TABLE 2B - Sizes and Diameter Tolerances, Sl UnitsFormNominal DiameterMillimetersToleranceMillimeterPlus and MinusCut Lengths 0.76, 0.89, 1.14 0.025Cut Lengths 1.57, 1.98, 2.39, 3.18, 3.96, 4.75 0.05Spools 0.18, 0.25, 0.38 0.0

    28、13Spools 0.51, 0.76, 0.89, 1.14 0.025Spools 1.57, 1.98, 2.39 0.05SAE INTERNATIONAL AMS5794F Page 5 of 6 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1.1), sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each heat or lot a

    29、s applicable.4.2.2 Periodic Tests: Determination of carbon and nitrogen on finished wire (3.1.1.1), weldability (3.4.1), cast (3.4.2.1), and helix (3.4.2.2) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampl

    30、ing and Testing: Shall be in accordance with AMS 2371 and as specified herein.4.4 Reports: The vendor of wire shall furnish with each shipment a report showing the results of tests for composition of each heat and stating that the wire conforms to the other technical requirements. This report shall

    31、include the purchase order number, heat and lot numbers, AMS 5794E, nominal size, and quantity.4.5 Resampling and Retesting: Shall be in accordance with AMS 2371.5. PREPARATION FOR DELIVERY: 5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths fo

    32、r manual welding. Wire on each spool or in each package of cut lengths shall be from the same heat of alloy.5.2 Alloy Verification: Wire from each spool or in each package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are rec

    33、ommended.5.2.1 An 8-inch (203-mm) length of wire shall be made accessible at both ends of each spool for alloy verification.5.3 Identification: Shall be in accordance with AMS 2816 unless AMS 2819 or another method is specified by purchaser.5.4 Packaging and Marking: Shall be in accordance with AMS

    34、2813 unless AMS 2814 or another method is specified by purchaser.SAE INTERNATIONAL AMS5794F Page 6 of 6 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Wire not conforming to this spec

    35、ification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specificatio

    36、n. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3

    37、 Dimensions in inch/pound units are primary; dimensions in Sl units are shown as the approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents shall specify not less than the following:AMS 5794ESize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “F“


    注意事项

    本文(SAE AMS 5794E-2002 Iron Alloy Corrosion and Heat-Resistant Welding Wire 31Fe - 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0Cb - 0 15N Annealed (UNS R30155)《31Fe 21Cr 20Ni 20Co 3 0Mo 2 5.pdf)为本站会员(sumcourage256)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开