欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5769F-2003 Alloy Corrosion and Heat-Resistant Bars Forgings and Rings 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0(Cb+Ta) - 0 15N - 32Fe Solution Heat Treated (UNS R30155)《固溶热处理.pdf

    • 资源ID:1022174       资源大小:67.63KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5769F-2003 Alloy Corrosion and Heat-Resistant Bars Forgings and Rings 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0(Cb+Ta) - 0 15N - 32Fe Solution Heat Treated (UNS R30155)《固溶热处理.pdf

    1、AEROSPACE MATERIAL SPECIFICATION AMS5769 REV. F Issued 1960-06 Revised 2003-10 Reaffirmed 2014-10 Superseding AMS5769E Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings,21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0(Cb+Ta) - 0.15N - 32Fe Solution Heat Treated (Composition similar to UNS R30155

    2、) RATIONALE AMS5769F has been reaffirmed to comply with the SAE five year review policy. _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicabilit

    3、y and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments

    4、 and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.

    5、 TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/st

    6、andards/AMS5769F 1. SCOPE: 1.1 Form: This specification covers a corrosion and heat-resistant alloy in the form of bars, forgings, flash welded rings, and stock for forging, flash welded rings, or heading. 1.2 Application: These products have been used typically for parts, such as turbine rotors, sh

    7、afts, blades, and bolts, requiring high strength up to 1350 F (732 C) and oxidation resistance up to 1800 F (982 C), but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specifica

    8、tion to the extent supplied herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 S

    9、AE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org. AMS 2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS 2261 Tolerances, Nickel, Nickel Alloy, and Cob

    10、alt Alloy Bars, Rods, and Wire AMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock AMS 2374 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steel and Alloy Forgings SAE INTERNATIONAL AMS5769F Page 2

    11、of 6 2.1 (Continued): AMS 2806 Identification, Bars, Wire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys AMS 2808 Identification, Forgings AMS 7490 Rings, Flash Welded, Corrosion and Heat-Resistant Austenitic Steels, Austenitic- Type Al

    12、loys, Nickel or Cobalt Alloys, or Precipitation-Hardenable Alloys 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM E 10 Brinell Hardness of Metallic Materials ASTM E 139 Conducting Creep, Creep-Rupture, and Stress-Rupture Tests

    13、 of Metallic Materials ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with AST

    14、M E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - Composition Element min max Carbon 0.08 0.16 Manganese 1.00 2.00 Silicon - 1.00 Phosphorus - 0.040 Sulfur - 0.030 Chromium 20.00 22.50 Nickel 19.00 21.00 Cobalt 18.50 21.00 Molybdenum 2.50 3.50 Tun

    15、gsten 2.00 3.00 Columbium 0.75 1.25 Nitrogen 0.10 0.20 Iron remainder SAE INTERNATIONAL AMS5769F Page 3 of 6 3.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2248. 3.2 Condition: The product shall be supplied in the following condition: 3.2.1 Bars, Forgings,

    16、 and Flash Welded Rings: Solution heat treated. Forgings shall be descaled. 3.2.1.1 Flash welded rings shall not be supplied unless specified or permitted on purchasers part drawing. When supplied, rings shall be manufactured in accordance with AMS 7490. 3.2.2 Stock for Forging, Flash Welded Rings,

    17、or Heading: As ordered by the forging, flash welded ring, or heading manufacturer. 3.3 Heat Treatment: Bars, forgings, and flash welded rings shall be solution heat treated by heating to 2150 F 25 (1177 C 14), holding at heat for not less than 1 hour, and quenching in water. 3.4 Properties: The prod

    18、uct shall conform to the following requirements: 3.4.1 Bars, Forgings, and Flash Welded Rings: 3.4.1.1 Hardness: Shall be as follows, determined in accordance with ASTM E 10: 3.4.1.1.1 Bars and Forgings: 156 to 217 HB, or equivalent (See 8.2). 3.4.1.1.2 Flash Welded Rings: 156 to 241 HB, or equivale

    19、nt (See 8.2). 3.4.1.2 Stress-Rupture Properties at 1350 F (732 C): A tensile specimen, maintained at 1350 F 3 (732 C 2) while a load sufficient to produce an initial axial stress of 32.0 ksi (221 MPa) or higher is applied continuously, shall not rupture in less than 23 hours. The test shall be conti

    20、nued to rupture without change of load. Elongation after rupture, measured at room temperature, shall be not less than 10% in 4D. Test shall be conducted in accordance with ASTM E 139. 3.4.1.2.1 The test of 3.4.1.2 may be conducted using incremental loading. In such case, the load required to produc

    21、e an initial axial stress of 32.0 ksi (221 MPa) or higher shall be used to rupture or for 23 hours, whichever occurs first. After the 23 hours and at intervals of 8 to 16 hours thereafter, the stress shall be increased in increments of 2.0 ksi (14 MPa). Time to rupture and elongation requirements sh

    22、all be as specified in 3.4.1.2. SAE INTERNATIONAL AMS5769F Page 4 of 6 3.4.2 Forging Stock: When a sample of stock is forged to a test coupon and heat treated as in 3.3, specimens taken from the heat treated coupon shall conform to the requirements of 3.4.1.1 and 3.4.1.2. If specimens taken from the

    23、 stock, after heat treatment as in 3.3. conform to the requirements of 3.4.1.1 and 3.4.1.2, the tests shall be accepted as equivalent to tests of a forged coupon. 3.4.3 Stock for Flash Welded Rings or Heading: Specimens taken from the stock, after heat treatment as in 3.3, shall conform to the requi

    24、rements of 3.4.1.1 and 3.4.1.2. 3.5 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5.1 Grain flow of die forgings, except in areas which contain flash-line

    25、 end grain, shall follow the general contour of the forgings showing no evidence of reentrant grain flow. 3.6 Tolerances: Bars shall conform to all applicable requirements of AMS 2261. 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samp

    26、les for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests: 4.2.1 Acceptance Tests

    27、: The following requirements are acceptance tests and shall be performed on each heat or lot as applicable: 4.2.1.1 Composition (3.1) of each heat. 4.2.1.2 Hardness (3.4.1.1) and stress-rupture properties (3.4.1.2) of each lot of bars, forgings, and flash welded rings. 4.2.1.3 Tolerances (3.6) of ba

    28、rs. 4.2.2 Periodic Tests: Tests of forging stock (3.4.2) and of stock for flash welded rings or heading (3.4.3) to demonstrate ability to develop required properties and grain flow of die forgings (3.5.1) are periodic tests and shall be performed at a frequency selected by the vendor unless frequenc

    29、y of testing is specified by purchaser. SAE INTERNATIONAL AMS5769F Page 5 of 6 4.3 Sampling: Shall be as follows: 4.3.1 Bars, Flash Welded Rings, and Stock for Forging, Flash Welded Rings, or Heading: In accordance with AMS 2371. 4.3.2 Forgings: In accordance with AMS 2374. 4.4 Reports: 4.4.1 The ve

    30、ndor of bars, forgings, and flash welded rings shall furnish with each shipment a report showing the results of tests for composition of each heat and for hardness and stress rupture properties of each lot, and stating that the product conforms to the other technical requirements. This report shall

    31、include the purchase order number, heat and lot numbers, AMS 5769F, size, and quantity. If forgings are supplied, the size and melt source of stock used to make the forgings shall also be included. 4.4.2 The vendor of stock for forging, flash welded rings, or heading shall furnish with each shipment

    32、 a report showing the results of tests for composition of each heat. This report shall include the purchase order number, heat number, AMS 5769F, size, and quantity. 4.5 Resampling and Retesting: Shall be as follows: 4.5.1 Bars, Flash Welded Rings, and Stock for Forging, Flash Welded Rings, or Headi

    33、ng: In accordance with AMS 2371. 4.5.2 Forgings: In accordance with AMS 2374. 5. PREPARATION FOR DELIVERY: 5.1 Sizes: Except when exact lengths or multiples of exact lengths are ordered, straight bars will be acceptable in mill lengths of 6 to 20 feet (1.8 to 6.1 m) but not more than 10% of any ship

    34、ment shall be supplied in lengths shorter than 10 feet (3 m). 5.2 Identification: Shall be as follows: 5.2.1 Bars: In accordance with AMS 2806. 5.2.2 Forgings: In accordance with AMS 2808. SAE INTERNATIONAL AMS5769F Page 6 of 6 5.2.3 Flash Welded Rings and Stock for Forging, Flash Welded Rings, or H

    35、eading: As agreed upon by purchaser and vendor. 5.3 Packaging: The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptan

    36、ce and safe delivery. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS: Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rej

    37、ection. 8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revis

    38、ion of the specification. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 8.2 Hardness conversion tables for metals are presented in ASTM E 140. 8.3 Terms used in AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch

    39、/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS 5769F Form and size or part number of product desired Quantity of product desired. 8.6 Key Words: Bars, forgings, rings, stress-rupture, UNS R30155 PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “F”


    注意事项

    本文(SAE AMS 5769F-2003 Alloy Corrosion and Heat-Resistant Bars Forgings and Rings 21Cr - 20Ni - 20Co - 3 0Mo - 2 5W - 1 0(Cb+Ta) - 0 15N - 32Fe Solution Heat Treated (UNS R30155)《固溶热处理.pdf)为本站会员(explodesoak291)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开