1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5679H AEROSPACE MATERIAL SPECIFICATION AMS5679 REV. H Issued 1951-11 Reaffirme
5、d 2008-11 Revised 2015-12 Superseding AMS5679G Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 73Ni - 15.5Cr - 2.2Cb - 8.0Fe (Composition similar to UNS N06062) RATIONALE AMS5679H has been updated to incorporate the standard quality requirements of AMS materials as the ordering requirements
6、 for AWS specified wire, and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion and heat resistant nickel alloy in the form of welding wire. 1.2 Application This wire has been used typically as bare wire filler metal for gas-tungsten-arc o
7、r gas-metal-arc welding of parts fabricated from alloys of similar composition, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. T
8、he supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE In
9、ternational, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2813 Packaging and Marking of Packages of Welding Wire, Standard Method AMS2814 Packaging and Marking of Packages of Welding Wire, Premium Quali
10、ty AMS2816 Identification, Welding Wire, Tab Marking Method SAE INTERNATIONAL AMS5679H Page 2 of 4 AMS2819 Identification, Welding Wire, Direct Color Code System ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire 2.2 AWS Publications Available from American Welding Societ
11、y, 8669 NW 36 Street, #130, Miami, FL 33166-6672, Tel: 1-800-443-9353 or 305-443-9353, www.aws.org. AWS A5.01 Welding Consumables-Procurement of Filler Metals and Fluxes AWS 5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods 3. TECHNICAL REQUIREMENTS Wire shall meet the
12、technical requirements of AWS A5.14 ERNiCrFe-5. 3.1 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances specified in AWS A5.14. Smaller diameter wires when ordered shall be supplied in sizes and tolerances shown in 3.1.1. 3.1.1 Diameter Shall be as shown in Table 1. Table
13、1A - Wire sizes and tolerances, inch/pound units Form Nominal Diameter Inch Tolerance Inch Plus Tolerance Inch Minus Cut Lengths Spools 0.030, 0.035, 0.045 0.007, 0.010, 0.015 0.001 0.0005 0.002 0.0005 Table 1B - Wire sizes and tolerances, SI units Form Nominal Diameter Millimeters Tolerance Millime
14、ter Plus Tolerance Millimeter Minus Cut Lengths Spools 0.76, 0.89, 1.14 0.18, 0.25, 0.38 0.025 0.013 0.05 0.013 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of the wire shall supply all samples for producers tests and shall be responsible for the performance of all
15、required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. SAE INTERNATIONAL AMS5679H Page 3 of 4 4.2 Classification of Tests 4.2.1 Acceptance Tests Composition, sizes and tolerances (3.1
16、), and alloy verification (5.1) are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing Shall be in accordance with AAWS A5.01 S3, testing schedule 5 or J. 4.4 Reports The producer of wire shall furnish with each shipment a report showing the results o
17、f tests for chemical composition of each heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5679H, nominal size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AWS A5.01. 5
18、. PREPARATION FOR DELIVERY 5.1 Alloy Verification 5.1.1 Wire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser and producer. The alloy verification methods of ARP4926 are recommended. 5.1.2 An 8 inch (203 mm) length of wire shall be made accessible
19、 at both ends of each spool for alloy verification. 5.2 Identification Shall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser. 5.3 Packaging and Marking Shall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser. 6. ACKNOWLE
20、DGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS5679H P
21、age 4 of 4 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicat
22、es a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit
23、 temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS5679H Size and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired. PREPARED BY AMS COMMITTEE “F“
