欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5596M-2017 Nickel Alloy Corrosion and Heat-Resistant Sheet Strip Foil and Plate 52 5Ni - 19Cr - 3 0Mo - 5 1Cb (Nb) - 0 90Ti - 0 50Al - 18Fe Consumable Electrode Remelted or.pdf

    • 资源ID:1022032       资源大小:266.49KB        全文页数:10页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5596M-2017 Nickel Alloy Corrosion and Heat-Resistant Sheet Strip Foil and Plate 52 5Ni - 19Cr - 3 0Mo - 5 1Cb (Nb) - 0 90Ti - 0 50Al - 18Fe Consumable Electrode Remelted or.pdf

    1、 _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising ther

    2、efrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this

    3、publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-49

    4、70 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS5596M AEROSPACE MATERIAL SPECIFICATION AMS5596 REV. M Issued 1964-01 Revised 2017-11 Supers

    5、eding AMS5596L Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, Foil and Plate 52.5Ni - 19Cr - 3.0Mo - 5.1Cb (Nb) - 0.90Ti - 0.50Al - 18Fe Consumable Electrode Remelted or Vacuum Induction Melted 1775 F (968 C) Solution Heat Treated (Composition similar to UNS N07718) RATIONALE AMS5596M res

    6、ults from a limited scope ballot to revise Heat Treatment (3.4.5), and also revises Reports (4.4) and Identification (5.1.1). 1. SCOPE 1.1 Form This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, foil, and plate 1.00 inch (25.4 mm) and under in thicknes

    7、s (see 8.5). 1.2 Application These products have been used typically for parts requiring resistance to creep and stress-rupture up to 1300 F (704 C) and oxidation resistance up to 1800 F (982 C), particularly those parts which are formed or welded and then heat treated to develop desired properties,

    8、 but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific d

    9、ocument issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-73

    10、23 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2262 Tolerances Nickel, Nickel Alloy, and Cobalt Alloy Sheet, Strip, and Plate AMS2269 Chemical Check Analysis Limits Nickel, Nickel Alloys, and Cobalt Alloys AMS2371 Quality Assurance Sampling and Testing Corrosion and Hea

    11、t-Resistant Steels and Alloys Wrought Products and Forging Stock SAE INTERNATIONAL AMS5596M Page 2 of 10 AMS2807 Identification Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys Sheet, Strip, Plate, and Aircraft Tubing ARP1917 Clarification of Terms Used in Aerospace Metals

    12、 Specifications AS4194 Sheet and Strip Surface Finish Nomenclature AS6279 Industry Standard Practices for Production, Distribution, and Procurement of Metal Stock 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610

    13、-832-9585, www.astm.org. ASTM A480/A480M Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM E3 Preparation of Metallographic Specimens ASTM E8/E8M Tension Testing of Metallic Materials ASTM E18 Rockwell Hardness of Metallic Materials ASTM E21 Elevated Temperature Tension Tes

    14、ts for Metallic Materials ASTM E112 Determining Average Grain Size ASTM E139 Conducting Creep, Creep-Rupture, and Stress-Rupture Tests of Metallic Materials ASTM E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness,

    15、 Knoop Hardness, Scleroscope Hardness, and Leeb Hardness ASTM E290 Bend Testing of Material for Ductility ASTM E354 Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys ASTM E384 Microindentation Hardness of Materials SAE INTERNATIONAL AMS559

    16、6M Page 3 of 10 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E354, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element Mi

    17、n Max Carbon - 0.08 Manganese - 0.35 Silicon - 0.35 Phosphorus - 0.015 Sulfur - 0.015 Chromium 17.00 21.00 Nickel 50.00 55.00 Molybdenum 2.80 3.30 Columbium (Niobium) 4.75 5.50 Titanium 0.65 1.15 Aluminum 0.20 0.80 Cobalt - 1.00 Tantalum - 0.05 Boron - 0.006 Copper - 0.30 Iron remainder 3.1.1 Check

    18、Analysis Composition variations shall meet the applicable requirements of AMS2269. 3.2 Melting Practice Alloy shall be multiple melted using consumable electrode practice in the remelt cycle or shall be induction melted under vacuum. If consumable electrode remelting is not performed in vacuum, elec

    19、trodes which have been produced by vacuum induction melting shall be used for remelting. 3.3 Condition The product shall be supplied in the following condition: 3.3.1 Sheet, Strip, and Foil Hot or cold rolled, solution heat treated, and, unless solution heat treatment is performed in an atmosphere y

    20、ielding a bright finish, descaled having a surface appearance in accordance with ASTM A480/A480M and AS4194 comparable to 3.3.1.1 and 3.3.1.2, as applicable, except that product 0.010 inch (0.25 mm) and under in nominal thickness shall have a surface appearance comparable to No. 2B finish. 3.3.1.1 S

    21、heet No. 2D finish. 3.3.1.2 Strip No. 1 strip finish. SAE INTERNATIONAL AMS5596M Page 4 of 10 3.3.2 Plate Hot rolled, solution heat treated, and, unless solution heat treatment is performed in an atmosphere yielding a bright finish, descaled. 3.4 Solution Heat Treatment 3.4.1 Product 0.050 Inch (1.2

    22、7 mm) and Over in Thickness Heat to a temperature within the range 1725 to 1825 F (941 to 996 C), hold at the selected temperature within 25 F (14 C) for a time commensurate with product thickness, and cool at a rate equivalent to an air cool or faster. 3.4.2 Product under 0.050 Inch (1.27 mm) in Th

    23、ickness No specific heat treating instructions are specified, but it is recommended that the product be solution heat treated by heating in a suitable protective atmosphere, preferably in hydrogen or argon (see 3.4.4) or in vacuum (10-4 Torr or less), to a temperature within the range 1725 to 1825 F

    24、 (941 to 996 C), holding at the selected temperature within 25 F (14 C) for a time commensurate with product thickness, and cooling at a rate equivalent to an air cool or faster. 3.4.3 The use of dissociated ammonia as protective atmosphere is not recommended. 3.4.4 For product 0.010 inch (0.25 mm)

    25、and under in nominal thickness, a dew point of -60 F (-50 C) or lower is preferable when using hydrogen or argon atmosphere. 3.4.5 Continuous Heat Treating - Process parameters (i.e., furnace temperature setpoints, heat input, travel rate, etc.) for continuous heat treating lines shall be establishe

    26、d by the material producer and validated by testing of product to specified requirements. 3.5 Properties Product, 1.00 inch (25.4 mm) and under in nominal thickness, shall conform to the following requirements: 3.5.1 As Solution Heat Treated 3.5.1.1 Tensile Properties Shall be as shown in Table 2, d

    27、etermined in accordance with ASTM E8/E8M. Table 2 Table 2A - Tensile properties, inch/pound units Nominal Thickness Inch Tensile Strength ksi, max Yield Strength at 0.2% Offset ksi, max Elongation in 2 Inches or 4D %, min Up to 0.010, incl 140 80.0 report Over 0.010 to 0.1874, incl 140 80.0 30 Over

    28、0.1874 to 1.00, incl 150 105 30 Table 2B - Tensile properties, SI units Nominal Thickness Millimeters Tensile Strength MPa, max Yield Strength at 0.2% Offset MPa, max Elongation in 50.8 mm or 4D %, min Up to 0.25, incl 965 552 report Over 0.25 to 4.760, incl 965 552 30 Over 4.760 to 25.4, incl 1034

    29、724 30 SAE INTERNATIONAL AMS5596M Page 5 of 10 3.5.1.2 Hardness Shall be not higher than shown in Table 3, or equivalent (see 8.2), determined in accordance with ASTM E18; for thin gages, where superficial hardness testing is impractical, microhardness testing in accordance with ASTM E384 may be use

    30、d. Product shall not be rejected on the basis of hardness if the tensile properties of 3.5.1.1 are acceptable, determined on specimens taken from the same sample as that with nonconforming hardness or from another sample with similar nonconforming hardness. Table 3 - Maximum hardness Nominal Thickne

    31、ss Inch Nominal Thickness Millimeters Hardness Up to 0.1874, incl Up to 4.760, incl 102 HRB Over 0.1874 to 1.00, incl Over 4.760 to 25.4, incl 25 HRC 3.5.1.3 Bending Product 0.1874 inch (4.760 mm) and under in nominal thickness shall be tested in accordance with ASTM E290 using a sample prepared nom

    32、inally 0.75 inch (19.0 mm) in width with its axis of bending parallel to the direction of rolling and shall withstand without cracking bending at room temperature through an angle of 180 degrees around a diameter equal to the bend factor shown in Table 4 times the nominal thickness of the product. T

    33、able 4 - Bending parameters Nominal Thickness Inch Nominal Thickness Millimeters Bend Factor Up to 0.050, incl Up to 1.27, incl 1 Over 0.050 to 0.1874, incl Over 1.27 to 4.760, incl 2 3.5.1.4 Average Grain Size Shall be as follows, determined in accordance with ASTM E112: 3.5.1.4.1 For Product 0.010

    34、 inch (0.25 mm) and Under in Nominal Thickness ASTM No. 8 or finer. 3.5.1.4.2 For Product Over 0.010 to 0.250 inch (0.25 to 6.35 mm), Inclusive, in Nominal Thickness ASTM No. 6 or finer. 3.5.1.4.3 For Product Over 0.250 inch (6.35 mm) in Nominal Thickness ASTM No. 4 or finer. 3.5.1.5 Surface Microst

    35、ructure Metallographic examination on the unetched and etched specimen cross-section of product 0.125 inch (3.18 mm) and under in thickness, shall disclose no alloy depleted surface layer (see 8.3.1), intergranular attack, or other detrimental surface conditions greater than 0.0005 inch (0.013 mm) f

    36、or product 0.060 inch (1.52 mm) and under in nominal thickness, or greater than 0.001 inch (0.025 mm) for product over 0.060 inch (1.52 mm) in nominal thickness. Other standards for acceptance or limits for product over 0.125 inch (3.18 mm) in thickness may be established by purchaser. Each specimen

    37、 shall be prepared according to ASTM E3 and evaluated at 500X magnification. SAE INTERNATIONAL AMS5596M Page 6 of 10 3.5.2 After Precipitation Heat Treatment The product shall have the following properties after being precipitation heat treated by heating to 1325 F 15 F (718 C 8 C), holding at heat

    38、for 8 hours 0.5 hour, cooling at a rate of 100 F 15 F (56 C 8 C) degrees per hour to 1150 F 15 F (621 C 8 C), holding at 1150 F 15 F (621 C 8 C) for 8 hours 0.5 hour, and cooling in air. Instead of the 100 F 15 F (56 C 8 C) degrees per hour cooling rate to 1150 F 15 F (621 C 8 C), product may be fur

    39、nace cooled at any rate provided the time at 1150 F 15 F (621 C 8 C) is adjusted to give a total precipitation heat treatment time of 18 hours. The product shall also meet the requirements of 3.5.2.1, 3.5.2.2, and 3.5.2.3 after being re-solution heat treated by heating to 1750 F 25 F (954 C 14 C), h

    40、olding at heat for 60 minutes 5 minutes, and cooling at a rate equivalent to an air cool or faster and precipitation heat treated as above. 3.5.2.1 Tensile Properties 3.5.2.1.1 At Room Temperature Shall be as shown in Table 5, determined in accordance with ASTM E8/E8M. Table 5 Table 5A - Minimum roo

    41、m temperature tensile properties, inch/pound units Nominal Thickness Inch Tensile Strength ksi Yield Strength at 0.2% Offset ksi Elongation in 2 Inches or 4D % Up to 0.010, incl 180 150 report Over 0.010 to 1.00, incl 180 150 12 Table 5B - Minimum room temperature tensile properties, SI units Nomina

    42、l Thickness Millimeters Tensile Strength MPa Yield Strength at 0.2% Offset MPa Elongation in 50.8 mm or 4D % Up to 0.25, incl 1241 1034 report Over 0.25 to 25.4, incl 1241 1034 12 3.5.2.1.2 At 1200 F (649 C) Shall be as shown in Table 6, determined in accordance with ASTM E21 on specimens heated to

    43、1200 F 5 F (649 C 3 C), held at heat for not less than 20 minutes before testing, and tested at 1200 F 5 F (649 C 3 C). Table 6 Table 6A - Minimum elevated temperature tensile properties, inch/pound units Nominal Thickness Inch Tensile Strength ksi Yield Strength at 0.2% Offset ksi Elongation in 2 I

    44、nches or 4D % Up to 0.025, incl 140 115 5 Over 0.025 to 1.00, incl 145 120 5 Table 6B - Minimum elevated temperature tensile properties, SI units Nominal Thickness Millimeters Tensile Strength MPa Yield Strength at 0.2% Offset MPa Elongation in 50.8 mm or 4D % Up to 0.64, incl 965 793 5 Over 0.64 to

    45、 25.4, incl 1000 827 5 SAE INTERNATIONAL AMS5596M Page 7 of 10 3.5.2.1.2.1 For product 0.010 inch (0.25 mm) and under in nominal thickness, properties may be established using a sample up to 0.025 inch (0.64 mm) in nominal thickness from the same master coil and heat. The suppliers certification of

    46、test shall indicate the thickness at which the elevated temperature tensile test was performed. Properties do not apply to product 0.010 inch (0.25 mm) and under, but product shall be produced from product under 0.025 inch (0.64 mm) that has met property requirements. 3.5.2.2 Hardness Shall be not l

    47、ower than 36 HRC, or equivalent (see 8.2), determined in accordance with ASTM E18; for thin gages, where superficial hardness testing is impractical, microhardness testing in accordance with ASTM E384 may be used. Product shall not be rejected on the basis of hardness if the tensile properties of 3.

    48、5.2.1.1 are acceptable, determined on specimens taken from the same sample as that with nonconforming hardness or from another sample with similar nonconforming hardness. 3.5.2.3 Stress-Rupture Properties at 1200 F (649 C) A tensile specimen, maintained at 1200 F 3 F (649 C 2 C) while a load sufficient to product the initial axial stress shown in Table 7 or higher stress is applied continuously, shall not rupture in less than 23 hours. The test shall be continued to rupture without change of load. Elongation after rupture, measured at room temperature, shall be not less than specified in T


    注意事项

    本文(SAE AMS 5596M-2017 Nickel Alloy Corrosion and Heat-Resistant Sheet Strip Foil and Plate 52 5Ni - 19Cr - 3 0Mo - 5 1Cb (Nb) - 0 90Ti - 0 50Al - 18Fe Consumable Electrode Remelted or.pdf)为本站会员(twoload295)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开