欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5562E-2010 Steel Corrosion and Heat Resistant Seamless Tubing 9 0Mn - 20Cr - 6 5Ni - 0 28N Solution Heat Treated (UNS S21904)《9 0Mn 20Cr 6 5Ni 0 28N溶液热处理的耐蚀和耐热无缝钢管》.pdf

    • 资源ID:1021996       资源大小:44.23KB        全文页数:6页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5562E-2010 Steel Corrosion and Heat Resistant Seamless Tubing 9 0Mn - 20Cr - 6 5Ni - 0 28N Solution Heat Treated (UNS S21904)《9 0Mn 20Cr 6 5Ni 0 28N溶液热处理的耐蚀和耐热无缝钢管》.pdf

    1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

    2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

    3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

    4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5562EAEROSPACEMATERIALSPECIFICATIONAMS5562 REV. E Issued 1974-06 Reaffirmed 2006-04 Revised

    5、2010-08 Superseding AMS5562D Steel, Corrosion and Heat Resistant, Seamless Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N Solution Heat Treated UNS S21904 RATIONALEAMS5562E revises sampling and testing (4.3.2) and results from a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specific

    6、ation covers a corrosion and heat resistant steel in the form of seamless tubing. 1.2 ApplicationThis tubing has been used typically for parts, such as fluid-conducting lines, requiring both corrosion and heat resistance, especially when such parts are welded or brazed during fabrication, and which

    7、require strength higher than that of the 18 8 type steels, or require oxidation resistance up to 1100 F (593 C), but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification

    8、to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE P

    9、ublications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2243 Tolerances, Corrosion and Heat-Resistant Steel Tubing AMS2248 Chemical Check Analysis Limits, Corrosion and He

    10、at-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock SAE AMS5562E Page 2 of 6AMS2634 Ultrasonic Inspection, Thin Wall Metal Tubing A

    11、MS2807 Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.or

    12、g.ASTM A 262 Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels ASTM A 370 Mechanical Testing of Steel Products ASTM A 450/A 450M General Requirements for Carbon, Ferritic Alloy and Austenitic Alloy Steel Tubes ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, M

    13、araging, and Other Similar Chromium-Nickel-Iron Alloys ASTM E 426 Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel and Similar Alloys ASTM E 1417 Liquid Penetrant Testing 3. TECHNICAL REQUIREMENTS 3.1 CompositionShall conform to the perce

    14、ntages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Carbon - 0.04 Manganese 8.00 10.00 Silicon - 1.00 Phosphorus - 0.060 Sulfur -

    15、 0.030 Chromium 19.00 21.50 Nickel 5.50 7.50 Nitrogen 0.15 0.40 Molybdenum - 0.75 Copper - 0.75 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. 3.2 ConditionSolution heat treated, and, unless solution heat treatment is performed in an atmosphere yieldin

    16、g a bright finish, pickled as required or passivated. SAE AMS5562E Page 3 of 63.3 Fabrication Tubing shall be produced by a seamless process. Any surface finishing operation applied to remove objectional sets and surface blemishes shall be performed prior to final solution heat treatment. A light po

    17、lish to improve external surface appearance may be employed after solution heat treatment and, if performed, the product shall be subsequently passivated.3.4 PropertiesTubing shall conform to the following requirements: 3.4.1 Tensile Properties Shall be as shown in Table 2, determined in accordance

    18、with ASTM A 370. TABLE 2 - MINIMUM TENSILE PROPERTIES Property Value Tensile Strength 90.0 ksi (621 MPa) Yield Strength at 0.2% Offset 50.0 ksi (345 MPa) Elongation in 2 Inches (50.8 mm)Strip Specimens Full Tube Specimens40% 45% 3.4.2 Flarability Specimens as in 4.3.1 shall withstand flaring at room

    19、 temperature, without formation of cracks or other visible defects, by being forced axially with steady pressure over a hardened and polished tapered steel pin having a 74-degree included angle to produce a flare having a permanent expanded OD not less than shown in Table 3. TABLE 3A - FLARABILITY,

    20、INCH/POUND UNITS Nominal OD InchesExpanded OD InchesNominal OD InchesExpanded OD Inches0.125 0.200 0.750 0.937 0.188 0.302 1.000 1.187 0.250 0.359 1.250 1.500 0.312 0.421 1.500 1.721 0.375 0.484 1.750 2.106 0.500 0.656 2.000 2.356 0.625 0.781 TABLE 3B - FLARABILITY, SI UNITS Nominal OD MillimetersEx

    21、panded OD MillimetersNominal OD MillimetersExpanded OD Millimeters3.18 5.08 19.05 23.80 4.78 7.67 25.40 30.15 6.35 9.12 31.75 38.10 7.92 10.69 38.10 43.71 9.52 12.29 44.45 53.49 12.70 16.66 50.80 59.84 15.88 19.84 3.4.2.1 Tubing with nominal OD between any two standard sizes shown in Table 3 shall t

    22、ake the same percentage flare as shown for the larger of the two sizes. SAE AMS5562E Page 4 of 63.4.3 Pressure Test The tubing shall show no bulges, leaks, pinholes, cracks, or other defects when subjected to an internal hydrostatic pressure (P), except that a diametric permanent set of 0.002 inch p

    23、er inch (0.002 mm/mm) of diameter is acceptable. The hydrostatic pressure (P) shall be determined using Equation 1: 2222DdPSDd=+(Eq. 1)where:P = Test pressure in ksi (MPa) S = Minimum yield strength from 3.4.1 D = Nominal OD d = Nominal ID 3.4.4 Susceptibility to Intergranular Attack Specimens from

    24、tubing, after sensitizing treatment, shall pass the intergranular corrosion test performed in accordance with ASTM A 262, Practice E. After exposure, tubing shall be tested in accordance with the flattening test requirements of ASTM A 450/A 450M. Samples shall be taken from tubing after final anneal

    25、ing but may be taken prior to cold working. 3.5 QualityTubing, as received by purchaser, shall be uniform in quality and condition and shall have a finish conforming to the best practice for high quality aircraft tubing. It shall be smooth and free from grease, oil and other foreign matter, heavy sc

    26、ale or oxide, burrs, seams, tears, grooves, laminations, slivers, pits, and other imperfections detrimental to usage of the tubing. Surface imperfections, such as handling marks, straightening marks, light mandrel and die marks, shallow pits, and scale pattern, will not be considered injurious if th

    27、e imperfections are removable within the tolerances specified for wall thickness, but removal of such imperfections is not required. 3.5.1 Tubing shall be free from grease or other foreign matter. Metallic flakes or particles shall not be collected by a clean, white cloth drawn through the length of

    28、 the bore of a test sample. Discoloration of the cloth, without the presence of flakes or particles, is acceptable. 3.5.2 When specified, tubing shall be subjected to fluorescent penetrant testing in accordance with ASTM E 1417, to ultrasonic inspection in accordance with AMS2634, to electromagnetic

    29、 (eddy- current) inspection in accordance with ASTM E 426, or to any combination thereof. Tubing shall meet the requirements of 3.5 and other acceptance criteria established by the cognizant engineering organization (See 8.4). 3.6 Tolerances Shall conform to all applicable requirements of AMS2243. 4

    30、. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of tubing shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensu

    31、re that the tubing conforms to specified requirements. SAE AMS5562E Page 5 of 64.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), tensile properties (3.4.1), nondestructive inspection when specified (3.5.2), and tolerances (3.6) are acceptance tests and shall be performed on each

    32、heat or lot as applicable. 4.2.2 Periodic Tests Flarability (3.4.2), pressure test (3.4.3), and susceptibility to intergranular attack (3.4.4) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.3 Sampling and Testi

    33、ng Shall be in accordance with AMS2371 and the following: 4.3.1 Specimens for flarability test (3.4.2) shall be full tubes or sections cut from a tube. The end of the specimen to be flared shall be cut square, with the cut end smooth and free from burrs, but not rounded. 4.3.2 When nondestructive in

    34、spection (3.5.2) is required, each length of tubing shall be inspected. 4.4 Reports The vendor of tubing shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile properties of each lot, and stating that the product conforms to the other tech

    35、nical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5562E, size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY 5.1 Sizes Except when exact lengths or multiples of exact lengths are ordered, st

    36、raight tubing will be acceptable in mill lengths of 6 to 20 feet (1.8 to 6.1 m) but not more than 10% of any shipment shall be supplied in lengths shorter than 10 feet (3 m). 5.2 IdentificationShall be in accordance with AMS2807.5.3 PackagingTubing shall be prepared for shipment in accordance with c

    37、ommercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the tubing to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotati

    38、ons and when acknowledging purchase orders. SAE AMS5562E Page 6 of 67. REJECTIONS Tubing not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in loc

    39、ating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications

    40、, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equiv

    41、alents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following AMS5562ESize of tubing desired Quantity of tubing desired Methods for nondestructive testing and standards for acceptance, when specified (See 3.5.2). PREPARED BY AMS COMMITTEE “F“


    注意事项

    本文(SAE AMS 5562E-2010 Steel Corrosion and Heat Resistant Seamless Tubing 9 0Mn - 20Cr - 6 5Ni - 0 28N Solution Heat Treated (UNS S21904)《9 0Mn 20Cr 6 5Ni 0 28N溶液热处理的耐蚀和耐热无缝钢管》.pdf)为本站会员(hopesteam270)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开