欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 5511H-2003 Steel Corrosion-Resistant Sheet Strip and Plate 19Cr - 9 5Ni (304L) Solution Heat Treated (UNS S30403)《UNS S30403经溶液热处理的19Cr-9 5Ni(304 L)耐蚀钢制片材 带材和板材》.pdf

    • 资源ID:1021953       资源大小:38.83KB        全文页数:5页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 5511H-2003 Steel Corrosion-Resistant Sheet Strip and Plate 19Cr - 9 5Ni (304L) Solution Heat Treated (UNS S30403)《UNS S30403经溶液热处理的19Cr-9 5Ni(304 L)耐蚀钢制片材 带材和板材》.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5511H AEROSPACE MATERIAL SPECIFICATION AMS5511 REV. H Issued 1949-11 Revised 2

    5、003-01 Reaffirmed 2013-08 Superseding AMS5511G Steel, Corrosion-Resistant, Sheet, Strip, and Plate 19Cr - 9.5Ni (304L) Solution Heat Treated (Composition similar to UNS S30403) RATIONALE This document has been reaffirmed to comply with the SAE 5-year Review policy. 1. SCOPE: 1.1 Form: This specifica

    6、tion covers a corrosion-resistant steel in the form of sheet, strip, and plate. 1.2 Application: These products have been used typically for formed and drawn parts requiring corrosion resistance up to 800 F (427 C), especially where such parts may require welding or brazing during fabrication, but u

    7、sage is not limited to such applications. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific docume

    8、nt issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org. AMS 2242 Tolerance

    9、s, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Sheet, Strip, and Plate AMS 2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS 2371 Quality Assurance Sampling and Testing,

    10、Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock SAE INTERNATIONAL AMS5511H Page 2 of 5 AMS 2807 Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing AS4194 Sheet and Strip Surface Fini

    11、sh Nomenclature 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM A 480/A 480M Flat Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip ASTM A 262 Detecting Susceptibility to Intergranular Attack in Austenitic Stai

    12、nless Steels ASTM E 8 Tension Testing of Metallic Materials ASTM E 8M Tension Testing of Metallic Materials (Metric) ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the per

    13、centages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 COMPOSITION Element min max Carbon - 0.030 Manganese - 2.00 Silicon - 1.00 Phosphorus - 0.040 Sulfur - 0.

    14、030 Chromium 18.00 20.00 Nickel 8.00 11.00 Molybdenum - 0.75 Copper - 0.75 3.1.1 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2248. SAE INTERNATIONAL AMS5511H Page 3 of 5 3.2 Condition: The product shall be supplied in the following condition: 3.2.1 Sheet and

    15、Strip: Cold rolled, solution heat treated, and, unless solution heat treatment is performed in an atmosphere yielding a bright finish, descaled having a surface appearance in accordance with ASTM A 480/A 480M and AS4194 comparable to 3.2.1.1 or 3.2.1.2, as applicable. 3.2.1.1 Sheet: No. 2D finish, e

    16、xcept No. 2B finish may be supplied if acceptable to purchaser (See 8.2.1). 3.2.1.2 Strip: No. 1 strip finish. 3.2.2 Plate: Hot or cold rolled, solution heat treated, and descaled. 3.3 Properties: The product shall conform to the following requirements: 3.3.1 Tensile Properties: Shall be as shown in

    17、 Table 2 for product over 0.005 inch (0.13 mm) in nominal thickness, determined in accordance with ASTM E 8 or ASTM E 8M. TABLE 2 - TENSILE PROPERTIES Property Value Tensile Strength, maximum 100 ksi (689 MPa) Elongation in 2 Inches (50.8 mm) or 4D, minimum 40% 3.3.2 Susceptibility to Intergranular

    18、Attack: The product, shall pass the intergranular corrosion test performed in accordance with ASTM A 262, Practice E. 3.4 Quality: The product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of t

    19、he product. 3.5 Tolerances: Shall conform to all applicable requirements of AMS 2242. 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser

    20、 reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. SAE INTERNATIONAL AMS5511H Page 4 of 5 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1), tensile properties (3.3.1), and toleran

    21、ces (3.5) are acceptance tests and shall be performed on each heat or lot as applicable. 4.2.2 Periodic Tests: Susceptibility to intergranular attack (3.3.2) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.3 Sam

    22、pling and Testing: Shall be in accordance with AMS 2371. 4.4 Reports: The vendor of the product shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile properties of each lot, and stating that the product conforms to the other technical req

    23、uirements. This report shall include the purchase order number, heat and lot numbers, AMS 5511H, size, and quantity. 4.5 Resampling and Retesting: Shall be in accordance with AMS 2371. 5. PREPARATION FOR DELIVERY: 5.1 Identification: Shall be in accordance with AMS 2807. 5.2 Packaging: The product s

    24、hall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT: A vendor shall mention this specifi

    25、cation number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS: Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS5511H Page 5 of 5 8. NOTES: 8.1 A change bar (|

    26、) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including t

    27、echnical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units are primary; dimensions and properties in SI units are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Procurement documents should specify not less than the following: AMS 5511H Form and size of product desired Quantity of product desired. PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “F”


    注意事项

    本文(SAE AMS 5511H-2003 Steel Corrosion-Resistant Sheet Strip and Plate 19Cr - 9 5Ni (304L) Solution Heat Treated (UNS S30403)《UNS S30403经溶液热处理的19Cr-9 5Ni(304 L)耐蚀钢制片材 带材和板材》.pdf)为本站会员(刘芸)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开