欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 3420F-2001 Dehydrating Agent Silica Gel《脱水剂硅胶》.pdf

    • 资源ID:1020982       资源大小:109.63KB        全文页数:10页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 3420F-2001 Dehydrating Agent Silica Gel《脱水剂硅胶》.pdf

    1、AEROSPACE MATERIAL SPECIFICATIONAMS 3420FIssuedRevisedSuperseding AMS 3420EDehydrating AgentSilica Gel1. SCOPE:1.1 Form: This specification covers silica gel dehydrating agent in the form of a granular powder in either plain or indicator grades.1.2 Application: This product has been used typically f

    2、or corrosion prevention of metals during storage in closed spaces, but usage is not limited to such applications.1.3 Classification: Covered by this specification are classified as follows:Grade D - Large particle size with indicatorGrade E - Medium particle size without indicatorGrade F - Medium pa

    3、rticle size with indicator type2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is

    4、 specified. When the referenced document has been canceled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AS167 Chart, Humidity Indicator, Color Comparis

    5、onReaffirmed 1942-032001-012010-05SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any p

    6、atent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserve

    7、d. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)

    8、 Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3420F Copyright SAE International Provided by IHS under li

    9、cense with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 3420F SAE AMS 3420F- 2 -2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM B 214 Sieve Analysis of Granular Metal Powder 3. TECHNICAL REQUIREMENT

    10、S: 3.1 Material:Material shall be non-deliquescent and shall absorb water by physical means and not by chemical combination except for the cobalt chloride in indicator grades.3.2 Properties:The product shall conform to the following requirements; tests shall be performed on the product supplied and

    11、in accordance with specified test methods:3.2.1 Composition:3.2.1.1 Grades D and F shall be silica gel containing not less than 99.6% Si02impregnated with not more than 1.5 pounds (0.68 kg) of anhydrous cobalt chloride (CoC12) per 100 pounds (45 kg) of finished material on a dry weight basis determi

    12、ned by test method acceptable to purchaser.3.2.1.2 Grade E shall be silica gel containing not less than 99.4% Si02on a dry weight basis.3.2.2 Color: Indicating grades shall have characteristic colors when in equilibrium with the atmosphere and shall closely match the colors shown on AS167 for relati

    13、ve humidities of 0, 20, 40 and 60% at 25 C 2 (77 F 4).3.2.3 Water Content: Shall not exceed 5.75% by weight for Grades D and F, determined in accordance with 4.4.1; no limit is established for Grade E.3.2.4 Water Vapor Adsorption Capacity: Shall be not lower than shown in Table 1 when in equilibrium

    14、 with the relative humidities given, determined as in 4.4.2.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 3420F SAE AMS 3420F- 3 -3.2.5 Particle Size: Shall be as shown in Table 2 for the respe

    15、ctive grades, determined in accordance with 4.4.3.3.2.6 Particle Strength: Shall be as shown in Table 3 for the respective grades, determined in accordance with 4.4.4.TABLE 1 - Water Vapor Adsorption CapacityRelative Humidity%Water Vapor Adsorption% by WeightGrades D and FWater Vapor Adsorption% by

    16、WeightGrade E10 4.3 5.720 8.6 10.540 18.2 21.560 27.7 28.080 32.9 31.2TABLE 2 - Particle Size DistributionScreenSize DistributionPercentGrade DSize DistributionPercentGrades E and FRetained on No. 6 (3.35 mm), maximum 2.0Through No. 6 (3.35 mm), Retained onNo. 12 (1.70 mm), minimum 55.0Through No. 1

    17、2 (1.70 mm), Retained onNo. 18 (1.00 mm), minimum 19.0Through No. 18 (1.00 mm), maximum 3.5Through No. 20 (850 m), maximum 0.5Retained on 0.530 inch (13.5 mm) opening 0.0Through 0.530 inch (13.5 mm) opening, retainedon No. 80 (180 m), minimum 96.0Through No. 80 (180 m), maximum 4.0Copyright SAE Inte

    18、rnational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 3420F SAE AMS 3420F- 4 -3.2.7 Corrosion: The product shall not have a corrosive effect on other materials when exposed to conditions normally encountered in service,

    19、 determined by a procedure acceptable to purchaser.Discoloration of metal shall not be considered objectionable.3.3 Quality:The drying agent, as received by purchaser, shall be a uniform in quality and condition and free from foreign materials and from imperfections detrimental to usage of the produ

    20、ct. 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of the product shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed neces

    21、sary to ensure that the product conforms to the requirements of this specification.4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.2.1), color (3.2.2), water content (3.2.3) and quality (3.3) are acceptance tests and shall be performed on each lot.4.2.2 Preproduction Tests: All t

    22、echnical requirements are preproduction tests and shall be performed prior to or on the initial shipment of the product to a purchaser, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required.4.3 Sampling and Testin

    23、g: Shall be as follows:4.3.1 For Acceptance Tests: Sufficient product shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three.TABLE

    24、 3 - Particle StrengthScreenPowderingGrade DPercentPowderingGrades E each bottle shall have not less than 500 mL capacity and shall be equipped with a petticoat bubbler. Pass air from a flowmeter through the saturator bottles at a rate of 14 cubic feet (0.4 m3) per minute; each bottle shall be fille

    25、d to 1/3 to 1/2 its volume with sulfuric acid of the proper concentration to give the desired relative humidity in accordance with Table 4. Pass the air from the saturator bottles through a mist trap, which can be an ordinary drying tube or cylinder approximately 1.5 inches (38 mm) in diameter and 8

    26、 to 9 inches (203 to 229 mm) high packed with glass wool, and then through the adsorption bulb, which can be a cylindrical bulb with a flat bottom, a short tubular arm, a top with a ground glass joint, and a tubular opening for the air to pass (See Figure 2). Duplicate sets of apparatus shall be pro

    27、vided to make simultaneous determinations for relative humidities of 10, 20, 40, 60 and 80% at temperature of 25 to 30 C, (77 to 86 F). Temperature change during a test shall be not greater than 1 C (2 F) degrees.TABLE 4 - Water Vapor AbsorptionRelative HumidityPercent at 25 to 30 CRelative Humidity

    28、Percent at 77 to 86 FSulfuric Acid SolutionPercent by Weight10 10 64.720 20 58.240 40 47.860 60 38.480 80 26.4Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 3420F SAE AMS 3420F- 6 -4.4.2.2 Place

    29、 5 to 10 grams of product, weighed to the nearest milligram, in a tared adsorption bulb. Do not expose the product to air any more than necessary. Make a tight rubber connection to the outlet of the mist trap and adjust air flow to 240 cubic inches 30 (4.0 L 0.5) per minute. After three hours, weigh

    30、 the adsorption bulb quickly; repeat the weighings until two successive weighings approximately one hour apart show a variation not greater than ten milligrams.Generally, the weight increase will rise to a maximum and then decrease slightly before reaching constant weight. The gain in weight, expres

    31、sed as a percentage of the original weight, is the percentage of water vapor the product will hold in equilibrium with air of the relative humidity attained in the saturators. The attained relative humidity in the saturators shall be determined on the exit end solution in each chain after the produc

    32、t has attained equilibrium.4.4.3 Particle Size: Bring a sample of the product to approximate equilibrium with the atmosphere.Place a five ounce (142 gram) sample of the product on the coarsest screen in a nest of the applicable sizes and shake for three minutes on a screen shaker. Equipment shall be

    33、 in accordance with ASTM B 214. 4.4.4 Particle Strength: Repeat the particle size test of 4.4.3. Mix separately, the portions of the Grade D sample retained on the No. 18 or coarser screens and the portion of Grade E or F retained on the No. 80 or coarser screens, bring to approximate equilibrium wi

    34、th the atmosphere, weigh out a 1.5-ounce 0.2 (43-gram 5) sample to an accuracy of 0.01 ounce (0.2 gram) and place on the No. 18 or No. 80 screen, as applicable, together with five copper disks approximately 0.50 inch thick and 0.750 inch in diameter (1.3 x 19 mm). Fit the screen with a tight cover a

    35、nd nest with a finer screen and a retaining pan; the finer screen shall be No. 30 for Grade D and No. 200 for Grades E and F. Shake the sample for 15 minutes in the apparatus specified in 4.4.3. Weigh the powder collected in the retaining pan and report as a percentage of the original sample weight.

    36、4.5 Reports:The vendor of the product shall furnish with each shipment a report showing the results of tests to determine conformance to the acceptance test requirements and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, lo

    37、t number, AMS 3420F, formula number, and quantity.4.6 Resampling and Retesting: If any specimen used in the above tests fails to meet the specified requirements, disposition of the product may be based on the results of testing three additional specimens for each original nonconforming specimen. Fai

    38、lure of any retest specimen to meet the specified requirements shall be cause for rejection of the product represented. Results of all tests shall be reported.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from

    39、IHS-,-,-AMS 3420F SAE AMS 3420F- 7 -5. PREPARATION FOR DELIVERY: 5.1 Identification:Dehydrating agent shall be assigned a unique name or other alphanumeric code identification traceable to a specific set of ingredients and raw materials, manufacturing processes and sequences, controls and inspection

    40、 processes. In the event of any change in ingredients, raw materials, manufacturing processes, inspection procedures, that name or other coded identification shall also be changed.5.1.1 Each package of product shall be permanently and legibly marked with not less than the following information:DEHYD

    41、RATING AGENT, SILICA GELAMS 3420FGRADE _SIZE OR PART NUMBER _LOT NUMBER _PURCHASE ORDER NUMBER _QUANTITY _MANUFACTURERS IDENTIFICATION (See 5.1.1) _5.2 Packaging:5.2.1 Packaging shall be accomplished to ensure that the product, during shipment and storage, will be protected against damage from expos

    42、ure to weather or any other normal hazard.5.2.2 A lot of dehydrating agent may be packaged in small quantities and delivered under the same basic lot designation provided lot identification is maintained.5.2.3 Packages of product shall be prepared for shipment in accordance with commercial practice

    43、and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery.6. ACKNOWLEDGMENT:A vendor shall mention this specification number and its revision letter in all quotations and when acknow

    44、ledging purchase orders.7. REJECTIONS:Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from I

    45、HS-,-,-AMS 3420F SAE AMS 3420F- 8 -8. NOTES:8.1 A change bar ( l ) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification.An (R) symbol to the left of the document ti

    46、tle indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Dimensions and properties in inch/pound units and the Celsius temperatures are primary; dime

    47、nsions and properties in SI units and the Fahrenheit temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.3 Purchase documents should specify not less than the following:AMS 3420FGrade desiredQuantity of product desired.8.4 Key Words: Co

    48、rrosion prevention, storagePREPARED UNDER JURISDICTION OF AMS COMMITTEE “B“Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AMS 3420F SAE AMS 3420F- 9 -FIGURE 1 - Apparatus for Water Vapor Adsorption TestsCopyright SAE International Provided by IHS under license w


    注意事项

    本文(SAE AMS 3420F-2001 Dehydrating Agent Silica Gel《脱水剂硅胶》.pdf)为本站会员(figureissue185)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开