欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 2451 13A-2017 Plating Brush Silver.pdf

    • 资源ID:1020631       资源大小:220.49KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 2451 13A-2017 Plating Brush Silver.pdf

    1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

    2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

    3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

    4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS2451/13A AEROSPACE MATERIAL SPECIFICATION AMS2451 /13 REV. A Issued 2002-12 Revised 2017-11

    5、Superseding AMS2451/13 Plating, Brush, Silver RATIONALE AMS2451/13A is the result of a Five-Year Review and update of this specification with a change to paragraph 3.2.2 hydrogen embrittlement. 1. SCOPE 1.1 Purpose This specification covers the engineering requirements and process for brush plating

    6、of silver by electrodeposition. It shall be used, in conjunction with AMS2451, for silver deposits. 1.2 Application This process has been used typically to provide low electrical contact resistance, prevent galling or seizing of surfaces of parts, and corrosion protection, but usage is not limited t

    7、o such applications. 1.3 Safety - Hazardous Materials Shall be in accordance with AMS2451. 2. APPLICABLE DOCUMENTS In addition to those listed in AMS2451, the issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herei

    8、n. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SA

    9、E International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2412 Plating, Silver, Copper Strike, Low Bake AMS2451 Plating, Brush, General Requirements SAE INTERNATIONAL AMS2451/13A Page 2 of 2 3. TECH

    10、NICAL REQUIREMENTS Shall be in accordance with AMS2451 and as follows. 3.1 Procedure 3.1.1 Silver shall be electrodeposited from a silver brush plating solution in accordance with processing instructions from the solution manufacturer. 3.1.2 The equipment, materials, and procedures used to process s

    11、pecimens and parts shall conform to a schedule of control factors (see AMS2451) and to the recommendations of the manufacturer of the selective plating equipment and processing materials. 3.1.3 A preliminary strike or bonding layer of nickel and copper, palladium or gold may be used. 3.2 Properties

    12、3.2.1 Thickness Where silver flash is specified, plate thickness shall be approximately 0.0001 inch (2.5 m). 3.2.2 Hydrogen Embrittlement Shall be in accordance with AMS 2451. 4. QUALITY ASSURANCE PROVISIONS: Shall be in accordance with AMS2451. 5. PREPARATION FOR DELIVERY Shall be in accordance wit

    13、h AMS2451. 6. ACKNOWLEDGEMENT Shall be in accordance with AMS2451. 7. REJECTIONS Shall be in accordance with AMS2451. 8. NOTES See AMS2451 and the following. 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisi

    14、ons, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Plating meeting the requirements of this specification will exhibit equivalent properties to plating produced in accordance with AMS2412. PREPARED BY AMS COMMITTEE “B”


    注意事项

    本文(SAE AMS 2451 13A-2017 Plating Brush Silver.pdf)为本站会员(registerpick115)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开