欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    SAE AMS 2242G-2008 Tolerances Corrosion and Heat Resistant Steel Iron Alloy Titanium And Titanium Alloy Sheet Strip and Plate《腐蚀公差和耐热钢、铁合金、钛和钛合金薄板材、带材和厚板材》.pdf

    • 资源ID:1020538       资源大小:531.10KB        全文页数:9页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    SAE AMS 2242G-2008 Tolerances Corrosion and Heat Resistant Steel Iron Alloy Titanium And Titanium Alloy Sheet Strip and Plate《腐蚀公差和耐热钢、铁合金、钛和钛合金薄板材、带材和厚板材》.pdf

    1、AEROSPACE MATERIAL SPECIFICATION AMS2242 REV. G Issued 1945-10 Revised 2008-06 Reaffirmed 2014-12 Superseding AMS2242F Tolerances Corrosion and Heat Resistant Steel, Iron Alloy, Titanium. And Titanium Alloy Sheet, Strip, and Plate RATIONALE AMS2242G has been reaffirmed to comply with the SAE five-ye

    2、ar review policy. _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringe

    3、ment arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved.

    4、 No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) T

    5、el: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS2242G 1. SCOPE This specification covers established manufac

    6、turing tolerances applicable to sheet, strip, and plate of corrosion and heat resistant steels, iron alloys, titanium, and titanium alloys ordered to inch dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “excl” is used to apply only to the higher figure of the s

    7、pecified range. 2. THICKNESS Thickness for sheet and strip is measured at any place on widths less than 1 inch, at any place 0.375 inch and over from an edge on widths 1 inch and over, and for plate at least 0.375 inch but not over 3 inches from an edge. 2.1 Sheet Table 1 includes crown tolerances.

    8、TABLE 1 Specified Thickness Inch Thickness Tolerance, Inch Plus and Minus For Width Ranges Shown Inches 24 to 48 incl Thickness Tolerance, Inch Plus and Minus For Width Ranges Shown Inches Over 48 Up to 0.005, incl 0.001 - Over 0.005 to 0.007, incl 0.0015 - Over 0.007 to 0.016, incl 0.002 - Over 0.0

    9、16 to 0.026, incl 0.003 0.003 Over 0.026 to 0.040, incl 0.004 0.004 Over 0.040 to 0.058, incl 0.004 0.005 Over 0.058 to 0.072, incl 0.005 0.006 Over 0.072 to 0.083, incl 0.005 0.007 Over 0.083 to 0.098, incl 0.006 0.008 Over 0.098 to 0.114, incl 0.007 0.009 Over 0.114 to 0.130, incl 0.008 0.010 Over

    10、 0.130 to 0.145, incl 0.010 0.012 Over 0.145 to 0.1875, excl 0.012 0.014 2.2 Strip Table 2 includes crown tolerances. TABLE 2 Specified Thickness Inch Thickness Tolerance Inch Plus and Minus For Width Ranges ShownInches 3/16 to 6, incl Thickness Tolerance Inch Plus and Minus For Width Ranges Shown I

    11、nches Over 6 to 12, incl Thickness Tolerance Inch Plus and Minus For Width Ranges ShownInches Over 12 to 24 excl 0.005 to 0.010, incl 0.10T 0.10T 0.10T Over 0.010 to 0.011, incl 0.0015 0.0015 0.0015 Over 0.011 to 0.013, incl 0.0015 0.0015 0.002 Over 0.013 to 0.017, incl 0.0015 0.002 0.002 Over 0.017

    12、 to 0.020, incl 0.0015 0.002 0.0025 Over 0.020 to 0.029, incl 0.002 0.0025 0.0025 Over 0.029 to 0.035, incl 0.002 0.003 0.003 Over 0.035 to 0.050, incl 0.0025 0.0035 0.0035 Over 0.050 to 0.069, incl 0.003 0.0035 0.0035 Over 0.069 to 0.100, incl 0.003 0.004 0.005 Over 0.100 to 0.125, incl 0.004 0.004

    13、5 0.005 Over 0.125 to 0.161, incl 0.0045 0.0045 0.005 Over 0.161 to 0.1875, excl 0.005 0.005 0.006 2.3 Plate Minus tolerances shall be 0.010 inch for all widths for all thicknesses up to 10.000 inches, inclusive, in all alloys; plus tolerances shall be as in Table 3. For circles, the plus thickness

    14、tolerances in Table 3 apply to the diameter of the circle corresponding to the width ranges shown. For plates of irregular shape, the plus thickness tolerances apply to the greatest width corresponding to the width ranges shown. TABLE 3 Specified Thickness Inches Thickness Tolerance, Inch, Plus For

    15、Width Ranges Shown Inches Over 10 to 84, incl Thickness Tolerance, Inch, Plus For Width Ranges Shown Inches Over 84 to 120, incl Thickness Tolerance, Inch, Plus For Width Ranges Shown Inches Over 120 to 144, incl Thickness Tolerance, Inch, Plus For Width Ranges ShownInches Over 144 0.1875 to 0.375,

    16、excl 0.045 0.050 - - 0.375 to 0.750, excl 0.055 0.060 0.075 0.090 0.750 to 1.000, excl 0.060 0.065 0.085 0.100 1.000 to 2.000, excl 0.070 0.075 0.095 0.115 2.000 to 3.000, excl 0.125 0.150 0.175 0.200 3.000 to 4.000, excl 0.175 0.210 0.245 0.280 4.000 to 6.000, excl 0.250 0.300 0.350 0.400 6.000 to

    17、8.000, excl 0.350 0.420 0.490 0.560 8.000 to 10.000, incl 0.450 0.540 0.630 - SAE INTERNATIONAL AMS2242G Page 2 of 9_ 3. WIDTH 3.1 Sheet 3.1.1 Stretcher Leveled, Resquared TABLE 4 Specified Thickness Inch Width Tolerance Inch, Plus Only For Width Ranges ShownInches 24 to 48, excl Width Tolerance Inc

    18、h, Plus Only For Width Ranges ShownInches 48 and Over Up to 0.131, excl 1/16 1/8 0.131 to 0.150, incl 1/8 1/8 Over 0.150 to 0.170, incl 3/16 3/16 Over 0.170 to 0.1875, excl 1/4 1/4 3.1.2 Not Resquared, Flat or in Coils TABLE 5 Specified WidthInches Width Tolerance, InchPlus Only 24 to 48, excl 1/16

    19、48 and over 1/8 3.2 Strip 3.2.1 Rolled Edge or Approximately Square Edge Produced by Rolling or Filing After Slitting TABLE 6 Specified Width Inches Specified Thickness Inch Width Tolerance, Inch Plus and Minus Up to 0.28125, incl Up to 0.0625, incl 0.005 Over 0.28125 to 0.750, incl Up to 0.09375, i

    20、ncl 0.005 Over 0.750 to 5.000, incl Up to 0.125, incl 0.005 Over 5.000 to 9.000, incl 0.008 to 0.125, incl 0.010 Over 9.000 to 20.000, incl 0.015 to 0.105, incl 0.010 Over 20.000 0.023 to 0.080, incl 0.015 3.2.2 Slit Edge TABLE 7 Specified Width Inches Width Tolerance, InchPlus and Minus For Thickne

    21、ss Ranges Shown Inch Up to 0.068, incl Width Tolerance, InchPlus and Minus For Thickness Ranges Shown Inch Over 0.068 to 0.099, incl Width Tolerance, Inch Plus and Minus For Thickness Ranges Shown Inch Over 0.099 to 0.160, incl Width Tolerance, InchPlus and Minus For Thickness Ranges Shown Inch Over

    22、 0.160 to 0.1875, excl 0.1875 to 0.500, incl 0.005 0.008 0.010 - Over 0.500 to 6.000, incl 0.005 0.008 0.010 0.016 Over 6.000 to 9.000, incl 0.005 0.010 0.016 0.020 Over 9.000 to 12.000, incl 0.010 0.010 0.016 0.020 Over 12.000 to 20.000, incl 0.016 0.016 0.020 0.031 Over 20.000 to 24.000, incl 0.02

    23、0 0.020 0.020 0.031 SAE INTERNATIONAL AMS2242G Page 3 of 9_ 3.3 Plate Minus tolerance shall be 1/4 inch for all widths and lengths in all thicknesses; plus tolerances shall be as shown in Table 8. TABLE 8 Specified Width Inches Specified Length Inches Width Tolerance, Inches Plus For Thickness Range

    24、s Shown Inch 3/16 to 3/8 excl Width Tolerance, Inches Plus For Thickness Ranges Shown Inch 3/8 to 1/2 incl Width Tolerance, Inches Plus For Thickness Ranges Shown Inches Over 1/2 to 1 incl Width Tolerance, Inches Plus For Thickness Ranges Shown Inches Over 1 Up to 48, incl 1/8 3/16 5/16 7/16 Over 48

    25、 to 60, incl 3/16 1/4 3/8 1/2 Over 60 to 84, incl Up to 144 incl 1/4 5/16 7/16 9/16 Over 84 to 108, incl 5/16 3/8 1/2 5/8 Over 108 3/8 7/16 5/8 3/4 Up to 48, incl 3/16 1/4 5/16 7/16 Over 48 to 60, incl 1/4 5/16 3/8 1/2 Over 60 to 84, incl 3/8 7/16 1/2 5/8 Over 84 to 108, incl Over 144 to 240 incl 7/

    26、16 1/2 5/8 3/4 Over 108 1/2 5/8 11/16 13/16 Up to 48, incl 1/4 5/16 3/8 1/2 Over 48 to 60, incl 5/16 3/8 1/2 5/8 Over 60 to 84, incl 7/16 1/2 5/8 3/4 Over 84 to 108, incl Over 240 to 360 incl 9/16 5/8 3/4 7/8 Over 108 5/8 11/16 7/8 1 Up to 60, incl 7/16 1/2 5/8 3/4 Over 60 to 84, incl 1/2 5/8 3/4 7/

    27、8 Over 84 to 108, incl 9/16 3/4 7/8 1 Over 108 Over 360 to 480, incl 3/4 7/8 1 1-1/8 Up to 60, incl 7/16 1/2 5/8 3/4 Over 60 to 84, incl 1/2 5/8 3/4 7/8 Over 84 to 108, incl 5/8 3/4 7/8 1 Over 108 Over 480 to 600, incl 3/4 7/8 1 1-1/8 Up to 60, incl 1/2 5/8 3/4 7/8 Over 60 to 108, incl Over 600 5/8

    28、3/4 7/8 1 Over 108 7/8 1 1-1/8 1-1/4 4. LENGTH 4.1 Sheet 4.1.1 Stretcher Leveled, Resquared TABLE 9 Specified Thickness Inch Specified LengthInches Length Tolerance Inch Plus Only Up to 0.131, incl Up to 120, excl 1/16 Up to 0.131, excl 120 and over 1/8 0.131 to 0.150, incl All 1/8 Over 0.150 to 0.1

    29、70, incl All 3/16 Over 0.170 to 0.1875, excl All 1/4 SAE INTERNATIONAL AMS2242G Page 4 of 9_ 4.1.2 Not Resquared TABLE 10 Specified Length Inches Length Tolerance,Inch Plus Only Up to 120, incl 1/4 Over 120 to 240, incl 1/2 4.2 Strip TABLE 11 Specified Length Inches Length Tolerance,Inch Plus Only U

    30、p to 60, incl 3/8 Over 60 to 120, incl 1/2 Over 120 to 240, incl 5/8 4.3 Plate Minus tolerances shall be 1/4 inch for all lengths and widths in all thicknesses; plus tolerances shall be as shown in Table 12. TABLE 12 Specified Width Inches Specified Length Inches Length Tolerance, Inches Plus For Th

    31、ickness Ranges Shown Inch 3/16 to 3/8 excl Length Tolerance, Inches Plus For Thickness Ranges Shown Inch 3/8 to 1/2 incl Length Tolerance, Inches Plus For Thickness Ranges Shown Inch Over 1/2 to 1 incl Length Tolerance, Inches Plus For Thickness Ranges Shown Inch Over 1 Up to 48, incl 3/16 1/4 3/8 1

    32、/2 Over 48 to 60, incl 1/4 5/16 7/16 9/16 Over 60 to 84, incl Up to 144, incl 5/16 3/8 1/2 5/8 Over 84 to 108, incl 3/8 7/16 9/16 11/16 Over 108 7/16 1/2 11/16 13/16 Up to 48, incl 3/8 1/2 5/8 3/4 Over 48 to 60, incl 7/16 5/8 3/4 7/8 Over 60 to 84, incl 1/2 11/16 3/4 7/8 Over 84 to 108, incl Over 14

    33、4 to 240, incl 9/16 3/4 7/8 1 Over 108 5/8 7/8 1 1-1/8 Up to 48, incl 1/2 5/8 3/4 7/8 Over 48 to 60, incl 5/8 3/4 3/4 7/8 Over 60 to 84, incl 11/16 3/4 7/8 1 Over 84 to 108, incl Over 240 to 360, incl 3/4 7/8 1 1-1/8 Over 108 7/8 1 1 1-1/8 Up to 60, incl 1-1/8 1-1/4 1-3/8 1-1/2 Over 60 to 108, incl

    34、1-1/4 1-3/8 1-1/2 1-5/8 Over 108 Over 360 to 480, incl 1-3/8 1-1/2 1-5/8 1-3/4 Up to 60, incl 1-1/4 1-1/2 1-5/8 1-3/4 Over 60 to 108, incl 1-3/8 1-1/2 1-5/8 1-3/4 Over 108 Over 480 to 600, incl 1-1/2 1-5/8 1-3/4 1-7/8 Up to 108, incl 1-3/4 1-7/8 1-7/8 2 Over 108 Over 600 1-3/4 2 2-1/4 2-3/8 SAE INTE

    35、RNATIONAL AMS2242G Page 5 of 9_ 5. STRAIGHTNESS 5.1 Sheet and Strip TABLE 13 Specified Width Inches Camber Tolerance, Inch, in Any 8 feet of Length Up to 1.500, incl 1/2 Over 1.500 to 24.000, excl 1/4 24.000 to 36.000, incl 1/8 Over 36.000 3/32 5.2 Plate Shall be of such straightness that the maximu

    36、m edgewise curvature (depth of arc) shall not exceed 1/8 inch in any 5 feet of length. 6. FLATNESS The following tolerances do not apply to strip, dead soft sheet, or deep drawing sheet for which there are no established tolerances. In all cases, the “Variation from Flat” is the maximum deviation fr

    37、om a horizontal flat surface. 6.1 Sheet, Not Stretcher Leveled The following table does not apply to cold worked tempers of austenitic grades. TABLE 14 Specified ThicknessInch Specified Width Inches Variation from Flat, Inch Up to 0.062, excl 24 to 36, incl 1/2 Over 36 to 60, incl 3/4 Over 60 1 0.06

    38、2 to 0.1875, excl 24 to 60, incl 1/2 Over 60 to 72, incl 3/4 Over 72 1 6.2 Cold Worked Austenitic Sheet, 1/4 and 1/2 Hard Tempers TABLE 15 Specified Thickness Inch Specified Width Inches Variationfrom FlatInches 1/4 Hard Variation from Flat Inches 1/2 Hard Up to 0.016, incl 1/2 3/4 Over 0.016 to 0.0

    39、30, incl 24 to 36, excl 5/8 7/8 Over 0.030 to 0.1875, excl 3/4 7/8 Up to 0.016, incl 5/8 1 Over 0.016 to 0.030, incl 36 to 48, incl 3/4 1-1/8 Over 0.030 to 0.1875, excl 1 1-1/8 SAE INTERNATIONAL AMS2242G Page 6 of 9_ 6.3 Sheet, Stretcher Leveled TABLE 16 Specified WidthInches Specified LengthInches

    40、Variation From Flat,Inch 24 to 48, incl Up to 96, incl 1/8 Over 96 1/4 Over 48 All 1/4 6.4 Plate The requirements of Table 17 apply to plate up to 15 feet, inclusive, in length, or to any 15 feet of longer plates. If the longer dimension is under 3 feet, the variation from flat shall be not greater

    41、than 1/4 inch in any direction. 6.4.1 Titanium plate, when specified to have “Special Flatness”, shall be creep flattened in a stress-free condition with deviation from flat not exceeding 0.060 inch in any 12 inches, with total deviation not exceeding 0.125 inch. SAE INTERNATIONAL AMS2242G Page 7 of

    42、 9_ TABLE 17 Specified Thickness Inches Variation from Flat Inches For Width Ranges Shown Inches Up to 48, incl Variation from Flat Inches For Width Ranges ShownInches Over 48 to 60, excl Variation from Flat Inches For Width Ranges ShownInches 60 to 72, excl Variation from Flat Inches For Width Rang

    43、es ShownInches 72 to 84, excl Variation from Flat Inches For Width Ranges Shown Inches 84 to 96, excl Variation from Flat Inches For Width Ranges Shown Inches 96 to 108, excl Variation from Flat Inches For Width Ranges ShownInches 108 to 120, excl Variation from Flat Inches For Width Ranges ShownInc

    44、hes 120 to 144, excl Variation from Flat Inches For Width Ranges Shown Inches 144 and over 0.1875 to 0.250, excl 3/4 1-1/16 1-1/4 1-3/8 1-5/8 1-5/8 1-7/8 2 - 0.250 to 0.375, excl 11/16 3/4 15/16 1-1/8 1-3/8 1-7/16 1-9/16 1-7/8 - 0.375 to 0.500, excl 1/2 9/16 11/16 3/4 15/16 1-1/8 1-1/4 1-7/16 1-3/4

    45、0.500 to 0.750, excl 1/2 9/16 5/8 5/8 13/16 1-1/8 1-1/8 1-1/8 1-3/8 0.750 to 1.000, excl 1/2 9/16 5/8 5/8 3/4 13/16 15/16 1 1-1/8 1.000 to 1.500, excl 1/2 9/16 9/16 9/16 11/16 11/16 11/16 3/4 1 1.500 to 4.000, excl 3/16 5/16 3/8 7/16 1/2 9/16 5/8 3/4 7/8 4.000 to 6.000, excl 1/4 3/8 1/2 9/16 5/8 3/4

    46、 7/8 1 1-1/8 SAE INTERNATIONAL AMS2242G Page 8 of 9_ 7. NOTES 7.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 7.2 Te


    注意事项

    本文(SAE AMS 2242G-2008 Tolerances Corrosion and Heat Resistant Steel Iron Alloy Titanium And Titanium Alloy Sheet Strip and Plate《腐蚀公差和耐热钢、铁合金、钛和钛合金薄板材、带材和厚板材》.pdf)为本站会员(花仙子)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开