1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS1534C AEROSPACE MATERIAL SPECIFICATION AMS1534 REV. C Issued 1983-01 Reaffirme
5、d 2004-02 Revised 2013-11 Superseding AMS1534B Cleaner, Aircraft Glass Window RATIONALE Changes in this revision include format/editorial changes as well update to specification revisions. 1. SCOPE 1.1 Form This specification covers two types of aircraft glass window cleaners in the form of a ready-
6、to-use liquid. 1.2 Application Primarily for removing soils, contaminants, and residues from aircraft glass windows by manual application. 1.3 Classification The cleaners covered by this specification shall be of the following types as ordered: Type I - Regular Type II - Antifogging 1.4 Safety - Haz
7、ardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure
8、familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this sp
9、ecification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall appl
10、y. SAE INTERNATIONAL AMS1534C Page 2 of 6 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2350 Standards and Test Methods AMS4041 Aluminum Alloy, Alclad
11、Sheet and Plate, 4.4Cu - 1.5Mg - 0.60Mn, Alclad 2024 and 1-1/2% Alclad 2024, -T3 Flat Sheet; 1-1/2% Alclad 2024-T351 Plate AMS4049 Aluminum Alloy Sheet and Plate, Alclad, 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (Alclad 7075; -T6 Sheet, -T651 Plate), Solution and Precipitation Heat Treated AMS4376 Magnesium A
12、lloy Plate, 3.0A1 - 1.0Zn (AZ31B-H26), Cold Rolled and Partially Annealed ARP1511 Corrosion of Low-Embrittling Cadmium Plate by Aircraft Maintenance Chemicals 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832
13、-9585, www.astm.org. ASTM D 56 Flash Point by Tag Closed Tester ASTM D 1015 Freezing Points of High-Purity Hydrocarbons ASTM D 1193 Reagent Water ASTM D 1568 Sampling and Chemical Analysis of Alkylbenzene Sulfonates ASTM F 483 Total Immersion Corrosion Test for Aircraft Maintenance Chemicals ASTM F
14、484 Stress Crazing of Acrylic Plastics in Contact with Liquid or Semi-Liquid Compounds ASTM F 485 Effects of Cleaners on Unpainted Aircraft Surfaces ASTM F 502 Effects of Cleaning and Chemical Maintenance Materials on Painted Aircraft Surfaces ASTM F 503 Preparing Aircraft Cleaning Compounds, Liquid
15、 Type, for Storage Stability Testing ASTM F 519 Mechanical Hydrogen Embrittlement Testing of Plating Processes and Aircraft Maintenance Chemicals ASTM F 1111 Standard Test Method for Corrosion of Low-Embrittling Cadmium Plate by Aircraft Maintenance Chemicals 2.3 U.S. Government Publications Availab
16、le from DLA Document Services, Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: (215) 697-6257, http:/quicksearch.dla.mil/. MIL-STD-2073-1 Standard Practice for Military Packaging MIL-STD-870 Cadmium Plating, Low Embrittlement, Electro-Deposition FED-STD-313 Material Safety Data S
17、heets, Preparation of SAE INTERNATIONAL AMS1534C Page 3 of 6 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall be optional with the manufacturer, shall be a homogenous liquid suitable for the intended usage, and shall meet the requirements of 3.2. 3.2 Properties Cleaner shall conform to the following
18、requirements; tests shall be performed in accordance with specified test methods on the product supplied: 3.2.1 Corrosion of Metal Surfaces 3.2.1.1 Total Immersion Corrosion The cleaner shall neither show evidence of corrosion nor cause a weight change of any test panel greater than the following, d
19、etermined in accordance with ASTM F 483: TABLE 1 Test Panel Weight Change mg/cm2per 24 hours AMS4041 Aluminum Alloy 0.3 AMS4049 Aluminum Alloy 0.4 AMS4376 Magnesium Alloy 0.8 3.2.1.2 Low-Embrittling Cadmium Plate Test panels, coated with low-embrittling cadmium plate, shall not show a weight change
20、greater than 1.0 mg/cm2per 24 hours, determined in accordance with ASTM F 1111. 3.2.2 Effect on Plastics The cleaner shall not craze, stain, or discolor transparent plastics, determined in accordance with ASTM F 484. 3.2.3 Effect on Painted Surfaces The cleaner shall neither decrease the hardness of
21、 polyurethane or other paint films specified by purchaser by more than two pencil hardness levels nor shall it produce any streaking, discoloration, or blistering of the paint film, determined in accordance with ASTM F 502. 3.2.4 Effect on Unpainted Surfaces The cleaner, tested in accordance with AS
22、TM F 485, shall neither produce streaking nor leave any stains requiring polishing to remove. 3.2.5 Hydrogen Embrittlement The product shall be non-embrittling, determined in accordance with ASTM F 519, utilizing Type 1a, 1c, or 2a specimens, cadmium plated in accordance with MIL-STD-870, Class 1, T
23、ype I. Type 1a and Type 1c specimens shall be loaded to 45% of the predetermined notch fracture strength, and Type 2a specimens loaded to 80% of the yield strength. The entire 2a stressed specimen, or just the notched area of the 1a and 1c stressed specimen, shall be immersed continuously in the sol
24、ution under test for 150 hours at a temperature between 20 and 30 C (68 to 86 F). 3.2.6 Flash Point Shall be not lower than 158 F (70 C), determined in accordance with ASTM D 56. SAE INTERNATIONAL AMS1534C Page 4 of 6 3.2.7 Freeze Point Shall be determined in accordance with ASTM D 1015 and the resu
25、lts reported. 3.2.8 Storage Stability The cleaner shall neither show separation from exposure to heat or cold nor show an increase in turbidity greater than a control sample equally diluted to use concentration with ASTM D 1193, Type IV, water, determined in accordance with ASTM F 503. 3.2.9 Antifog
26、ging, Type II Only The cleaner shall produce a definite antifogging action, determined in accordance with 3.2.9.1. 3.2.9.1 Make a 6 x 12 inch (152 x 305 mm) mirror test plate by splitting a standard 12 inch (305 mm) square mirror. Thoroughly clean the surface with isopropyl alcohol and rinse with AS
27、TM D 1193, Type IV, water. A white highly-reflective appearance is taken on by the glass in those areas not thoroughly clean. Apply the cleaner to one-half of the surface by wiping until the surface is just damp and allow to dry. Hold the mirror 6 inches (152 mm) from a steam source (cool steam). Th
28、ere should be a definite difference between the two halves of the surface. 3.2.10 Performance The cleaner, when used in accordance with manufacturers recommendations, shall remove soils, contaminants, and residues from aircraft glass windows, determined by procedures agreed upon by purchaser and ven
29、dor. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of the cleaner shall supply all samples for vendors tests and shall be responsible for performing all required tests. Results of such tests shall be reported to the purchaser as required by 4.5. Purchaser reserves the
30、right to sample and to perform any confirmatory testing deemed necessary to ensure that the cleaner conforms to the requirements of this specification. 4.2 Classification of Tests 4.2.1 Acceptance Tests Tests to determine conformance to requirements for effect on plastics (3.2.2) and effect on unpai
31、nted surfaces (3.2.4) are classified as acceptance tests and shall be performed on each lot. 4.2.2 Periodic Tests Tests to determine conformance to requirements for corrosion of metal surfaces (3.2.1), effect on painted surfaces (3.2.3), hydrogen embrittlement (3.2.5), flash point (3.2.6), freeze po
32、int (3.2.7), storage stability (3.2.8), and, for Type II, antifogging ability (3.2.9), are classified as periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.2.3 Preproduction Tests Tests to determine conformance to all
33、technical requirements of this specification are classified as preproduction tests and shall be performed prior to or on the initial shipment of cleaner to a purchaser, when a change in material and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be re
34、quired. 4.2.3.1 For direct U.S. Military procurement, substantiating test data and, when requested, preproduction test material shall be submitted to the cognizant agency as directed by the procuring activity, contracting officer, or request for procurement. SAE INTERNATIONAL AMS1534C Page 5 of 6 4.
35、3 Sampling Shall be in accordance with all applicable requirements of ASTM D 1568; a lot shall be all cleaner produced in one continuous manufacturing operation from the same batches of raw materials under the same fixed conditions and presented for vendors inspection at one time. 4.4 Approval 4.4.1
36、 Sample cleaner shall be approved by purchaser before cleaner for production use is supplied, unless such approval be waived by purchaser. Results of tests on production cleaner shall be essentially equivalent to those on the approved sample. 4.4.2 Vendor shall use ingredients, manufacturing procedu
37、res, and methods of inspection on production cleaner which are essentially the same as those used on the approved sample. If necessary to make any change in ingredients or in manufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients, processing,
38、or both and, when requested, sample cleaner. Production cleaner made by the revised procedure shall not be shipped prior to receipt of reapproval. 4.5 Reports The vendor of cleaner shall furnish with each shipment a report showing the results of tests to determine conformance to the acceptance test
39、requirements and, when performed, to the periodic test requirements and stating that the cleaner conforms to the other technical requirements of this specification. This report shall include the purchase order number, AMS1534C, manufacturers identification, lot number, and quantity. 4.5.1 A material
40、 safety data sheet conforming to FED-STD-313, or equivalent, shall be supplied to each purchaser prior to, or concurrent with, the report of preproduction test results or, if preproduction testing be waived by purchaser, concurrent with the first shipment of cleaner for production use. Each request
41、for modification of cleaner formulation shall be accompanied by a revised data sheet for the proposed formulation. 4.6 Resampling and Retesting If any sample used in the above tests fails to meet the specified requirements, disposition of the cleaner may be based on the results of testing three addi
42、tional samples for each original nonconforming sample. Failure of any retest sample to meet the specified requirements shall be cause for rejection of the cleaner represented and no additional testing shall be permitted. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identif
43、ication Each container shall be legibly marked with not less than AMS1534C, purchase order number, manufacturers identification, type number, lot number, and quantity. 5.2 Packaging: 5.2.1 Cleaner shall be packaged in containers of a type and size agreed upon by purchaser and vendor. 5.2.2 Container
44、s of cleaner shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the cleaner to ensure carrier acceptance and safe delivery. Packaging shall conform to carrier rules
45、 and regulations applicable to the mode of transportation. 5.2.3 For direct U.S. Military procurement, packaging shall be in accordance with Mil-STD-2073-1E, Level A or Level B, as specified in the request for procurement. Commercial packaging as in 5.2.1 and 5.2.2 will be acceptable if it meets the
46、 requirements of Level B. SAE INTERNATIONAL AMS1534C Page 6 of 6 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Cleaner not conforming to this specification, or to modifications author
47、ized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the doc
48、ument title indicates a complete revision of the document, including technical changes. Change bars and (R) are not use in original publications, nor in documents that contain editorial changes only. 8.2 For direct U.S. Military procurement, purchase documents should specify not less than the follow
49、ing: AMS1534C Type and size of containers desired Quantity of cleaner desired Procedure for determination of performance (See 3.2.10) Applicable level of packaging (See 5.2.3). 8.3 Cleaner meeting the requirements of this specification has been classified under Federal Supply Classification (FSC) 6850. PREPARED BY AMS COMMITTEE “J”
