欢迎来到麦多课文档分享! | 帮助中心 海量文档,免费浏览,给你所需,享你所想!
麦多课文档分享
全部分类
  • 标准规范>
  • 教学课件>
  • 考试资料>
  • 办公文档>
  • 学术论文>
  • 行业资料>
  • 易语言源码>
  • ImageVerifierCode 换一换
    首页 麦多课文档分享 > 资源分类 > PDF文档下载
    分享到微信 分享到微博 分享到QQ空间

    NFPA 13 AMD 5-2015 Standard for the Installation of Sprinkler Systems (Effective Date 09 07 2015).pdf

    • 资源ID:1008270       资源大小:105.39KB        全文页数:2页
    • 资源格式: PDF        下载积分:10000积分
    快捷下载 游客一键下载
    账号登录下载
    微信登录下载
    二维码
    微信扫一扫登录
    下载资源需要10000积分(如需开发票,请勿充值!)
    邮箱/手机:
    温馨提示:
    如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
    如需开发票,请勿充值!如填写123,账号就是123,密码也是123。
    支付方式: 支付宝扫码支付    微信扫码支付   
    验证码:   换一换

    加入VIP,交流精品资源
     
    账号:
    密码:
    验证码:   换一换
      忘记密码?
        
    友情提示
    2、PDF文件下载后,可能会被浏览器默认打开,此种情况可以点击浏览器菜单,保存网页到桌面,就可以正常下载了。
    3、本站不支持迅雷下载,请使用电脑自带的IE浏览器,或者360浏览器、谷歌浏览器下载即可。
    4、本站资源下载后的文档和图纸-无水印,预览文档经过压缩,下载后原文更清晰。
    5、试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。

    NFPA 13 AMD 5-2015 Standard for the Installation of Sprinkler Systems (Effective Date 09 07 2015).pdf

    1、 Tentative Interim Amendment NFPA 13 Standard for the Installation of Sprinkler Systems 2016 Edition Reference: Table 9.2.6.3.1, A.9.2.6.3.1 and Table 9.2.6.5.3 TIA 16-5 (SC 15-8-18 / TIA Log #1185) Note: Text of the TIA was issued and incorporated into the document prior to printing, therefore no s

    2、eparate publication is necessary. 1. Revise Table 9.2.6.3.1 to read as follows: Table 9.2.6.3.1 Maximum Pipe Stand HeightsaSystem Pipe Diameter cPipe Stand Diameterb11/2 in. 2 in. 21/2 in. 3 in. 4 in. 6 in.11/2 in. 6.6 ft 9.4 ft 11.3 ft 13.8 ft 18.0 ft 26.8 ft2 in. 4.4 ft 9.4 ft 11.3 ft 13.8 ft 18.0

    3、 ft 26.8 ft21/2 in. 8.1 ft 11.3 ft 13.8 ft 18.0 ft 26.8 ft3 in. 5.2 ft 11.3 ft 13.8 ft 18.0 ft 26.8 ft4 in. up to and including 8 in. 14.7 ft 26.8 fta. For SI units, 1 in. = 25.4 mm; 1 ft = 0.305 m. b. Pipe stands are Schedule 40 pipe. c. System piping is assumed to be Schedule 40 (8in. is Schedule

    4、30). 2. Revise section A.9.2.6.3.1 to read as follows: A.9.2.6.3.1 When a pipe stand does not resist lateral (e.g., earthquake or wind) forces, its maximum height and the weight of pipe it can support are based primarily on a limiting slenderness ratio (Kl/r), and on the axial and bending stresses c

    5、aused by the vertical load applied at a specified eccentricity. The pipe stand heights presented in Table 9.2.6.3.1 have been calculated using a “K” of 2.1 (i.e., assuming the pipe stand is an individual cantilever column) and a slenderness ratio limit of 300, except where combined axial and bending

    6、 stresses caused by the vertical load at an eccentricity of 12 in. (0.30 m) controls the design. In these cases, the pipe stand height is reduced such that the allowable axial stress (Fa) is sufficient to limit the combined axial stress ratio (fa/Fa, i.e., actual axial stress divided by allowable ax

    7、ial stress) plus the bending stress ratio (fb/Fb, i.e., actual bending stress divided by allowable bending stress) to 1.0. Two cases are considered, a vertical load at a 12 in. (0.30 m) eccentricity equal to: a) 5 times the weight of the water-filled pipe plus 250 lb (114 kg) using a bending stress

    8、allowable of 28,000 psi (193 MPa), and b) the weight of the water-filled pipe plus 250 lb (114 kg) using a bending stress allowable of 15,000 psi (103 MPa). No drift limit was imposed. When an engineering analysis is conducted, different pipe stand heights could be calculated if other assumptions ar

    9、e warranted based on actual conditions. For example, K=1.0 can be used if the pipe at the top of the pipe stand is braced in both horizontal directions, or a shorter cantilever column could be used to limit drift. Pipe stands are intended to be a single piece of pipe. For lengths that require joinin

    10、g pipes they should be welded to ensure the strength is maintained. 3. Revise Table 9.2.6.5.3 and replace the Note to read as follows: Table 9.2.6.5.3 Required Section Modulus for Pipe Stand Horizontal Support Arms (in3) Nominal Diameter of Pipe Being Supported (in.) 1 11/4 11/2 2 21/2 3 31/2 4 5 6

    11、8 Section Modulus Schedule 10 Steel 0.22 0.23 0.24 0.25 0.30 0.36 0.42 0.49 0.66 0.85 1.40 Section Modulus Schedule 40 Steel 0.22 0.24 0.24 0.27 0.36 0.45 0.54 0.63 0.86 1.13 1.64 For SI units, 1 in. = 25.4 mm. Note: The table is based on the controlling section modulus determined for a concentrated

    12、 load at a 1 ft (0.3 m) cantilever using: a) a maximum bending stress of 15 ksi (103 MPa) and a concentrated load equal to the weight of 15 ft (4.6 m) of water-filled pipe plus 250 lb (114 kg), or 2) a maximum bending stress of 28 ksi (193 MPa) and a concentrated load equal to five times the weight of 15 ft (4.6 m) of water-filled pipe plus 250 lb (114 kg). Issue Date: August 18, 2015 Effective Date: September 7, 2015 (Note: For further information on NFPA Codes and Standards, please see www.nfpa.org/codelist) Copyright 2015 All Rights Reserved NATIONAL FIRE PROTECTION ASSOCIATION


    注意事项

    本文(NFPA 13 AMD 5-2015 Standard for the Installation of Sprinkler Systems (Effective Date 09 07 2015).pdf)为本站会员(syndromehi216)主动上传,麦多课文档分享仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文档分享(点击联系客服),我们立即给予删除!




    关于我们 - 网站声明 - 网站地图 - 资源地图 - 友情链接 - 网站客服 - 联系我们

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1 

    收起
    展开